Tweco 200DC Inverter Arc Welding Machine User Manual

200ac/dc operating manual, Inverter, Arc welding machine

A-11217

200AC/DC

Operating Manual

Revision: AB

Issue Date: March 29, 2012 Manual No.: 0-5207

Operating Features:

inverter

ArC welDing MAChine

This manual is related to the following products:

200AC Inverter Arc Welding Machine

Table of contents

Document Outline

0-5143-CCr
SECTION 1:ARC WELDING SAFETY INSTRUCTIONS AND WARNINGS
- 1.01 Arc Welding Hazards
- 1.02 Principal Safety Standards
- 1.03 Declaration of Conformity
SECTION 2:INTRODUCTION
- 2.01 How To Use This Manual
- 2.02 Equipment Identification
- 2.03 Receipt of Equipment
- 2.04 Symbol Chart
- 2.05 Description
- 2.06 User Responsibility
- 2.07 Transporting Methods
- 2.08 Packaged Items
- 2.09 Duty Cycle
- 2.10 Specifications
- 2.11 Options and Accessories
SECTION 3:INSTALLATION, OPERATION AND SETUP
- 3.01 Environment
- 3.02 Location
- 3.03 Ventilation
- 3.04 Mains Supply Voltage Requirements
- 3.05 High Frequency Introduction
- 3.06 High Frequency Interference
- 3.07 Electromagnetic Compatibility
- 3.08 WELDSKILL 200AC/DC Power Source Controls, Indicators and Features
- 3.09 WELDSKILL 200AC/DC - STICK Programming Mode
- 3.10 WELDSKILL 200AC/DC – LIFT TIG and HF TIG Programming Mode
- 3.11 Short Circuit Protection While Welding
- 3.12 Shielding Gas Regulator Operating Instructions
- 3.13 Setup for TIG (GTAW) Welding with Gas Shielding
- 3.14 Setup for STICK (MMAW) Welding
SECTION 4:BASIC WELDING GUIDE
- 4.01 Stick (MMAW) Basic Welding Technique
- 4.02 Stick (MMAW) Welding Troubleshooting
- 4.03 TIG (GTAW) Basic Welding Technique
- 4.04 TIG (GTAW) Welding Problems
SECTION 5:POWER SOURCE PROBLEMS AND ROUTINE SERVICE REQUIREMENTS
- 5.01 Basic Troubleshooting
- 5.02 Power Source Problems
- 5.03 Routine Service and Calibration Requirements
- 5.04 Cleaning the Welding Power Source
SECTION 6:KEY SPARE PARTS
- 6.01 Power Source
APPENDIX: CIRCUIT DIAGRAM
CIGWELD - LIMITED WARRANTY TERMS
TERMS OF WARRANTY – January 2012
WARRANTY SCHEDULE – January 2012
GLOBAL CUSTOMER SERVICE CONTACT INFORMATION
SECTION 1: ARC WELDING SAFETY INSTRUCTIONS AND WARNINGS
- 1.01 Arc Welding Hazards
- 1.02 Principal Safety Standards
SECTION 2: INTRODUCTION
- 2.01 How To Use This Manual
- 2.02 Equipment Identification
- 2.03 Receipt Of Equipment
- 2.04 Symbol Chart
- 2.05 Description
- 2.06 User Responsibility
- 2.07 Transporting Methods
- 2.08 Packaged Items
- 2.09 Duty Cycle
- 2.10 Specifications
- 2.11 Options and Accessories
SECTION 3: INSTALLATION, OPERATION AND SETUP
- 3.01 Environment
- 3.02 Location
- 3.03 Ventilation
- 3.04 Mains Supply Voltage Requirements
- 3.05 Electromagnetic Compatibility
- 3.06 Transmig 175i Power Source Controls, Indicators and Features
- 3.07 Attaching the Tweco Professional Fusion Mig Torch (Euro)
- 3.08 Installing Minispool (100mm diameter)
- 3.09 Installing Handispool (200mm diameter)
- 3.14 Shielding Gas Regulator Operating Instructions
- 3.17 Setup for TIG (GTAW) Welding
- 3.18 Setup for Manual Arc (MMAW) Welding
SECTION 4: BASIC WELDING GUIDE
- 4.03 Stick (MMAW) Basic Welding Technique
- 4.04 Stick (MMAW) Welding Troubleshooting
- 4.05 TIG (GTAW) Basic Welding Technique
- 4.06 TIG (GTAW) Welding Problems
SECTION 5: POWER SOURCE PROBLEMS AND ROUTINE SERVICE REQUIREMENTS
- 5.01 Power Source Problems
- 5.02 Routine Service and Calibration Requirements
- 5.03 Cleaning the Welding Power Source
AP0-5143-APENDIX
CIGWELD - LIMITED WARRANTY TERMS
TERMS OF WARRANTY - JULY 2010
WARRANTY SCHEDULE - JULY 2010
GLOBAL CUSTOMER SERVICE CONTACT INFORMATION