V. description of use – Bowers Group UniCal Universal Digital Caliper User Manual
Page 55
55
55
55
55
IV.2 Switch off
Press the [set] button for 2 seconds.
It is not possible to switch off the instrument if you are in mode for introduction of tolerances or preset.
IV.3 Battery replacement
Changing the battery is necessary when indicator 'B' is displayed. (See XI.1)
After introduction of a new battery the instrument will be in mode 'Measure' and should display 0.000 mm (0.00mm).
If this is not correct, proceed with setting procedure. (See XI.1)
V. Description of use
V.1 Measuring modes
V.1.1 Selection of unit of measurement
Press quickly the [mode] button to change reading mm/inch (only applicable to dual units reading instruments).
See also other documents in the category Bowers Group Measuring instruments:
- Advanced Electronic/Air Column PC-2200 (33 pages)
- Baty - Calmaster Digital Caliper (2 pages)
- Baty - Dial Depth Gauge (1 page)
- Baty - Digital Depth Caliper (2 pages)
- Baty - Heavy Duty Digital Height Gauge (1 page)
- Baty - Digital Indicator - DI-1 (1 page)
- Baty - Digital Indicator - DI-2/3 (1 page)
- Baty - Digital Tyre Tread Depth Gauge (1 page)
- Baty - Hardened Stainless Steel Frame Dial Caliper (1 page)
- Baty - Large Digital Workshop Caliper - DC-60 (2 pages)
- Baty - Lever Type Dial Test Indicator BL-9 / BL-10 (1 page)
- Baty - Lever Type Dial Test Indicator BL Series (1 page)
- MicroGauge 2 Point Bore Gauge (13 pages)
- Snapmatic (5 pages)
- Ultima Bore Gauge (7 pages)
- XT500 Large Diameter Bore Gauge (2 pages)
- XTA Analogue Bore Gauge (9 pages)
- XTD Digital Bore Gauge (12 pages)
- XTH Holematic Bore Gauge (12 pages)
- XTL Lever Bore Gauge (2 pages)
- M&W Digitronic Bore Gauge 316 Series (1 page)
- M&W Value Line Digitronic Micrometer 270 Series (2 pages)
- M&W Digitronic Level 570 Series (2 pages)
- M&W Mechanical Depth Gauge 172 Series (1 page)
- M&W Dial Caliper 142 Series (1 page)
- M&W Digitronic Height Gauge 196 Series (1 page)
- M&W Universal Digital Protractor (2 pages)
- M&W Digital Caliper DFC Series (1 page)
- M&W Large Digitronic Workshop Caliper 150 Series (2 pages)
- M&W Digitronic Depth Gauge 172 Series (1 page)
- M&W Digitronic Height Gauge 191 Series (1 page)
- M&W Digitronic Micrometer 201 Series (2 pages)
- M&W Digitronic Indicator 405 Series (1 page)
- M&W Digitronic Indicator 410 Series (1 page)
- M&W Test Indicator 420 & 421 Series (1 page)
- M&W Test Indicator 422 Series (1 page)
- Countersink Gauge Measurement (2 pages)
- External Ball Screw measurement (1 page)
- Groove measurement (1 page)
- Internal Spline measurement (1 page)
- Internal Thread measurement (1 page)
- Universal Gauge with extra long measuring arms (1 page)
- Sylvac D100S Readouts (74 pages)
- Sylvac Opto Instruments (18 pages)