Rockwell Automation GV3000/SE AC Gen. Purpose & Vector Bookshelf Drive Start-Up and Reference Manual - Manual (Page 226)

Index-2 GV3000/SE AC Bookshelf Drive Software Reference, Version 6.06
G
General Parameters, 4-6 to 4-54
default settings, E-1 to E-3
First Menu, 4-6 to 4-10
listed alphabetically, A-1 to A-2
Second Menu, 4-11 to 4-90
H
H parameters, 4-55 to 4-67
default settings, E-3
listed alphabetically, A-2
High DC Bus Fault Avoidance Enable (U.024), 4-82
I
Identification Request (H.020), 4-66
Identification Result (H.019), 4-65
Inertia Compensation Gain (U.027), 4-83
Input Power/Snubber Configuration (H.017), 4-63
Input, analog
adjusting for external signal errors, G-3
configuring, G-2
using as speed or trim reference, G-2
using for vector torque reference, G-4
using to start and stop drive, G-5
Input, analog, see also
Option Port:Communication Loss Response
(P.062)
Terminal Strip Analog Input Configure (P.011)
Terminal Strip Analog Input Gain (P.010)
Terminal Strip Analog Input Offset (P.009)
Trim Reference Source (P.014)
Input, digital
configuring when RMI board is installed, F-1
Input, digital, see also
Preset Speed 1 Through Preset Speed 8
(P.031 to P.038)
Terminal Strip Digital Inputs Configure (P.007)
Terminal Strip Speed Reference Source
(P.008)
J
Jog Ramp Accel Time (P.021), 4-27
Jog Ramp Decel Time (P.022), 4-28
Jog Speed Reference (P.020), 4-27
K
Key descriptions, 3-6 to 3-7
Keypad/display, 3-1 to 3-9
see also Control Source (P.000)
L
LEDs
drive status, 3-8
monitor mode, 3-9
Level Sense Start Enable (P.054), 4-44
Line Dip Ride-Through Time (P.042), 4-37
Losses Compensation Gain (U.028), 4-84
Low DC Bus Fault Avoidance Enable (U.023), 4-81
M
Machinery Safety Standard EN 60204-1, drive
compliance with, D-1
Magnetizing Current (U.006), 4-73
Manual Reference Preset Enable (P.053), 4-43
Maximum Speed (P.004), 4-9
Minimum Speed (P.003), 4-9
Monitor mode, 3-2 to 3-3
Monitor mode LEDs, 3-9
MOP Accel/Decel Time (P.023), 4-28
MOP Reset Configuration (P.024), 4-29
Motor Nameplate Amps (H.002), 4-56
Motor Nameplate Amps (U.004), 4-71
Motor Nameplate Base Frequency (H.001), 4-55
Motor Nameplate Base Frequency (U.003), 4-71
Motor Nameplate Horsepower (U.022), 4-81
Motor Nameplate RPM (U.005), 4-72
Motor Nameplate Volts (H.000), 4-55
Motor Nameplate Volts (U.007), 4-73
Motor operated potentiometer, see MOP
Motor Overload Enable (P.040), 4-36
Motor Overload Type (P.041), 4-36
Motor Poles (U.002), 4-70
Motor thermal overload, see Motor Overload
Enable
Motor Top Speed (U.017), 4-78
N
Network Connection Type (Run/Program
Response) (P.061), 4-48
Network Drop Number (P.060), 4-48
Network option board,
see AutoMax Network
Option Board, ControlNet Network Option
Board, DeviceNet Network Option Board,
Profibus Interface Board
Network Output Register 1 Source through Network
Output Register 4 Source (P.066 to
P.069), 4-51