Danger – Sulky Cultiline HRW 1000 User Manual
Page 8

6
FR
4
2
4
3
1
DANGER
1
Beware the risk of crushing posed by the
hitch + seed drill hitch
2
Do not go on top of the harrow
3
Rotating shaft
4
Moving parts
the power take-off comply with the manufacturer’s
instructions.
9 - Before engaging power take-off, ensure that no
persons or animals are close to the machine.
10 - Never engage the power take-off when the
tractor engine is switched off.
11 - Disengage power take-off when the
universal drive shaft angle limits laid down by the
manufacturer are in danger of being exceeded.
12 - Caution! When power take-off has been
disengaged, moving parts may continue to rotate
for a few moments. Do not approach until they have
reached a complete standstill.
13 - On removal from the machine, rest the universal
drive shafts on the specially provided supports.
14 - After disconnecting the universal drive shafts
from the power take-off, the protective cap should be
fitted to the power take-off.
15 - Damaged power take-off and universal drive
shaft guards must be replaced immediately.
HYDRAuLIc cIRcuIT
1 - Caution! The hydraulic circuit is pressurized.
2 - When fitting hydraulic motors or cylinders,
ensure that the circuits are connected correctly in
accordance with the manufacturer’s guidelines.
3 - Before fitting a hose to the tractor’s hydraulic
circuit, ensure that the tractor-side and machine-side
circuits are not pressurized.
4 - The user of the machine is strongly recommended
to identify the hydraulic couplings between the
tractor and the machine in order to avoid wrong
connection. Caution! There is a danger of reversing
the functions (for example: raise/lower).
5 - Inspect the hydraulic remote-control cables
regularly. Any that are damaged or worn must be
replaced immediately.
The maximum working life for hoses is 6 years.
When replacing them, ensure that only hoses with
the specifications and grade recommended by the
machine manufacturer are used.
6 - When a leak is found, all necessary precautions
should be taken to avoid accidents.
7 - Beware of burns to hands when changing the
gears in the gearbox (when this is necessary).
Pressurized liquid, particularly hydraulic circuit oil,
may cause serious injury if it comes into contact
with the skin. If the case of injury, consult a doctor
immediately. There is a risk of infection.
8 - Before carrying out any work on the hydraulic
system, lower the machine, release the pressure from
the system, switch the engine off and remove the key
from the ignition.
mAINTENANcE
1 - It is essential before carrying out any servicing,
maintenance or repair work, or when checking for
the source of a breakdown or malfunction (also
when clearing plant debris or removing stones),
that the power take-off be disengaged, the engine
switched off and the keys taken out of the ignition.
2 - Check regularly that nuts and screws are not
loose. Tighten if necessary.
3 - Before carrying out maintenance work on a
raised machine, prop it up using appropriate means
of support.
4 - When replacing a working part wear protective
gloves and only use appropriate tools.
5 - To protect the environment, it is forbidden to
throw away oil, grease or filters of any kind. Give
them to specialist recycling firms.
6 - Before operating on the electric circuit, disconnect
the power source.
7 - Protective devices likely to be exposed to wear
and tear should be checked regularly. Replace them
immediately if they are damaged.
8 - Spare parts should comply with the standards
and specifications laid down by the manufacturer.
Only use Sulky spare parts.
9 - Before commencing any electric welding work
on the tractor or the towed machine, disconnect the
alternator and battery cables.
10 - Repairs affecting parts under stress or pressure
(springs, pressure accumulators, etc.) should be
carried out by suitably qualified engineers with
special tools.
GB