Kinze 3600 Lift and Rotate Planter (70 CM) Rev. 5/14 User Manual
Operator’s manual, Model 3600 twin-line export planter
Table of contents
Document Outline
- Table of Contents
- Overview
- Machine Operation
- Manual Safety Lockup
- Row Marker Safety Lockup
- Tongue Safety Pin
- Transport Latch Locking Pin
- Initial Preparation
- Tractor Requirements
- Tractor Preparation and Hookup
- Cylinder Information
- Hydraulic Hose Information
- Level Planter
- Ridge Planting
- Contact Wheel Spring Adjustment
- Contact Wheel Drive Sprockets
- Seed Rate Transmission Adjustment
- Wrap Spring Wrench Operation
- Shear Protection
- Hydraulic/Electric Operation
- Transport to Field Sequence
- Field Operation
- Planting Speed
- Field to Transport Sequence
- EdgeVac System
- Digital Vacuum Readout
- Vacuum Fan Motor Valve Block Assembly
- Analog Vacuum or Pressure Gauge
- Rock Guards
- Auxiliary Work Lights Package
- Row Marker Operation
- Row Marker Speed Adjustment
- Even-Row Push Row Unit
- Row Marker Adjustments
- Row Marker Even-Row Length Adjustment
- Offset Hitch Adjustment
- Point Row Clutches
- Two-Speed Point Row Clutches
- Auxiliary Hydraulic Option
- Rear Trailer Hitch
- Field Test
- Field Check Seed Population
- Determining Pounds Per Hectare (Brush-Type Meter)
- Field Check Granular Chemical Application
- Row Unit Operation
- Planting Depth
- “V” Closing Wheel Adjustment (Rubber or Cast Iron)
- Closing Wheel Shield (Rubber or Cast Iron “V” Closing Wheels)
- Drag Closing Attachment
- Covering Discs/Single Press Wheel Adjustment
- Seed Hoppers
- Seed Meter Drive Release
- Row Unit Extension Brackets
- Row Unit Chain Routing
- Quick Adjustable Down Force Springs Option (Standard or Heavy Duty)
- Interplant Push Row Unit Clutch Sprocket
- Interplant Push Row Unit Lockups
- Interplant Push Row Unit Vacuum Hose Shutoff
- Brush-Type Seed Meter
- Finger Pickup Seed Meter
- EdgeVac Seed Meters
- Seed Meter Cleanout
- Additives
- Frame Mounted Coulter (Pull Row Only)
- Residue Wheels (for Frame Mounted Coulter)
- Row Unit Mounted Disc Furrower (Pull Row Only)
- Row Unit Mounted Bed Leveler (Pull Row Only)
- Row Unit Mounted Residue Wheel
- Row Unit Mounted No Till Coulter
- Coulter Mounted Residue Wheels
- Granular Chemical Hopper and Drive
- Spring Tooth Incorporator
- Granular Chemical Banding Options
- Granular Chemical Bander Shield
- Interplant Push Row Unit Lockups
- Fertilizer
- Rate Charts
- Lubrication and Maintenance
- Lubrication
- Lubrication Symbols
- Sealed Bearings
- Wrap Spring Wrench Assembly
- Drive Chains
- Bushings
- Center Post
- U-Joint Slides
- Wheel Bearings
- Grease Fittings
- Mounting Bolts and Hardware
- Tire Servicing
- Finger Pickup Seed Meter Inspection/Adjustment
- Cleaning Finger Pickup Seed Meter For Storage
- Brush-Type Seed Meter Maintenance
- Cleaning Brush-Type Seed Meter For Storage
- Vacuum Manifold Maintenance
- EdgeVac Seed Meter Maintenance
- EdgeVac Seed Meter Cleanout
- Chain Tension Adjustment
- Drag Closing Attachment
- Gauge Wheel Adjustment
- Gauge Wheel Arm Bushing/Seal Replacement
- Gauge Wheel Arm Pivot Spindle Replacement
- 15" Seed Opener Disc Blade/Bearing Assembly
- Seed Tube Guard/Inner Scraper
- Frame Mounted Coulter
- Residue Wheels (For Use With Frame Mounted Coulter)
- Row Unit Mounted Disc Furrower
- Row Unit Mounted Bed Leveler
- Row Unit Mounted No Till Coulter
- Coulter Mounted Residue Wheels
- Row Unit Mounted Residue Wheel
- Granular Chemical Attachment
- Spring Tooth Incorporator
- Single and Two-Speed Point Row Clutch Maintenance
- Check Valve (Lift System)
- Check Valve (Vacuum Fan)
- Flow Control Valve
- Pressure Relief Valve
- Pressure Reducing Relief Valve
- Relief Valve Cartridge
- Solenoid Valve
- Row Marker Bearing Lubrication or Replacement
- Row Marker Transport Stand Adjustment
- Wheel Bearing Repack or Replacement
- Wear Pad Field Replacement/Adjustment
- Preparation for Storage
- Electrical Wiring Diagram for Light Package
- Electrical Control Console Schematic
- Electrical Wiring Harness Schematic (On Tractor)
- Electrical Wiring Harness Schematic (On Planter)
- Valve Block - Located on Hitch
- Valve Block - Located on Rear Center Frame
- Electrical Control Console Schematic (With Optional Two-Speed Point Row Clutches) and Wiring Harness at Two-Speed Point Row Clutch Solenoids
- Hydraulic System Schematic
- Hydraulic Schematic - Vacuum Fan Motor System
- Wing Down Pressure Schematic (Weight Transfer Mechanism)