Kinze 3600 Lift and Rotate Planter (70 CM) Rev. 5/14 User Manual
Operator’s manual, Model 3600 twin-line export planter
MODEL 3600
TWIN-LINE EXPORT PLANTER
OPERATOR’S MANUAL
M0249-01
Rev. 5/14
This manual is for:
Model 3600 Twin-Line
®
Planters
- 16 Row 70 CM “Y
” Hitch; 2013 production to 2014 production
Record model number and serial number of your planter along with date purchased:
Model Number __________________________________
Serial Number ___________________________________
Date Purchased __________________________________
Monitor Serial Number _______________________________________________
Measured Pulses Per Mile/Km (Radar Distance Sensor) ____________________
Measured Pulses Per Mile/ Km (Magnetic Distance Sensor) _________________
Kinze
®
, the Kinze
®
logo, Twin-Line
®
, Interplant
®
and EdgeVac
®
are registered trademarks of Kinze Manufacturing, Inc.
SERIAL NUMBER
Record your serial number and purchase date above for quick reference.
The serial number provides important information about your planter and is required to obtain correct replacement
parts. Always provide planter model and serial number to your Kinze Dealer when ordering parts or anytime
correspondence is made with Kinze Manufacturing, Inc.
Serial number plate location - left side of hitch
3600
Serial number plate location - R.H. Wing
Document Outline
- Table of Contents
- Overview
- Machine Operation
- Manual Safety Lockup
- Row Marker Safety Lockup
- Tongue Safety Pin
- Transport Latch Locking Pin
- Initial Preparation
- Tractor Requirements
- Tractor Preparation and Hookup
- Cylinder Information
- Hydraulic Hose Information
- Level Planter
- Ridge Planting
- Contact Wheel Spring Adjustment
- Contact Wheel Drive Sprockets
- Seed Rate Transmission Adjustment
- Wrap Spring Wrench Operation
- Shear Protection
- Hydraulic/Electric Operation
- Transport to Field Sequence
- Field Operation
- Planting Speed
- Field to Transport Sequence
- EdgeVac System
- Digital Vacuum Readout
- Vacuum Fan Motor Valve Block Assembly
- Analog Vacuum or Pressure Gauge
- Rock Guards
- Auxiliary Work Lights Package
- Row Marker Operation
- Row Marker Speed Adjustment
- Even-Row Push Row Unit
- Row Marker Adjustments
- Row Marker Even-Row Length Adjustment
- Offset Hitch Adjustment
- Point Row Clutches
- Two-Speed Point Row Clutches
- Auxiliary Hydraulic Option
- Rear Trailer Hitch
- Field Test
- Field Check Seed Population
- Determining Pounds Per Hectare (Brush-Type Meter)
- Field Check Granular Chemical Application
- Row Unit Operation
- Planting Depth
- “V” Closing Wheel Adjustment (Rubber or Cast Iron)
- Closing Wheel Shield (Rubber or Cast Iron “V” Closing Wheels)
- Drag Closing Attachment
- Covering Discs/Single Press Wheel Adjustment
- Seed Hoppers
- Seed Meter Drive Release
- Row Unit Extension Brackets
- Row Unit Chain Routing
- Quick Adjustable Down Force Springs Option (Standard or Heavy Duty)
- Interplant Push Row Unit Clutch Sprocket
- Interplant Push Row Unit Lockups
- Interplant Push Row Unit Vacuum Hose Shutoff
- Brush-Type Seed Meter
- Finger Pickup Seed Meter
- EdgeVac Seed Meters
- Seed Meter Cleanout
- Additives
- Frame Mounted Coulter (Pull Row Only)
- Residue Wheels (for Frame Mounted Coulter)
- Row Unit Mounted Disc Furrower (Pull Row Only)
- Row Unit Mounted Bed Leveler (Pull Row Only)
- Row Unit Mounted Residue Wheel
- Row Unit Mounted No Till Coulter
- Coulter Mounted Residue Wheels
- Granular Chemical Hopper and Drive
- Spring Tooth Incorporator
- Granular Chemical Banding Options
- Granular Chemical Bander Shield
- Interplant Push Row Unit Lockups
- Fertilizer
- Rate Charts
- Lubrication and Maintenance
- Lubrication
- Lubrication Symbols
- Sealed Bearings
- Wrap Spring Wrench Assembly
- Drive Chains
- Bushings
- Center Post
- U-Joint Slides
- Wheel Bearings
- Grease Fittings
- Mounting Bolts and Hardware
- Tire Servicing
- Finger Pickup Seed Meter Inspection/Adjustment
- Cleaning Finger Pickup Seed Meter For Storage
- Brush-Type Seed Meter Maintenance
- Cleaning Brush-Type Seed Meter For Storage
- Vacuum Manifold Maintenance
- EdgeVac Seed Meter Maintenance
- EdgeVac Seed Meter Cleanout
- Chain Tension Adjustment
- Drag Closing Attachment
- Gauge Wheel Adjustment
- Gauge Wheel Arm Bushing/Seal Replacement
- Gauge Wheel Arm Pivot Spindle Replacement
- 15" Seed Opener Disc Blade/Bearing Assembly
- Seed Tube Guard/Inner Scraper
- Frame Mounted Coulter
- Residue Wheels (For Use With Frame Mounted Coulter)
- Row Unit Mounted Disc Furrower
- Row Unit Mounted Bed Leveler
- Row Unit Mounted No Till Coulter
- Coulter Mounted Residue Wheels
- Row Unit Mounted Residue Wheel
- Granular Chemical Attachment
- Spring Tooth Incorporator
- Single and Two-Speed Point Row Clutch Maintenance
- Check Valve (Lift System)
- Check Valve (Vacuum Fan)
- Flow Control Valve
- Pressure Relief Valve
- Pressure Reducing Relief Valve
- Relief Valve Cartridge
- Solenoid Valve
- Row Marker Bearing Lubrication or Replacement
- Row Marker Transport Stand Adjustment
- Wheel Bearing Repack or Replacement
- Wear Pad Field Replacement/Adjustment
- Preparation for Storage
- Electrical Wiring Diagram for Light Package
- Electrical Control Console Schematic
- Electrical Wiring Harness Schematic (On Tractor)
- Electrical Wiring Harness Schematic (On Planter)
- Valve Block - Located on Hitch
- Valve Block - Located on Rear Center Frame
- Electrical Control Console Schematic (With Optional Two-Speed Point Row Clutches) and Wiring Harness at Two-Speed Point Row Clutch Solenoids
- Hydraulic System Schematic
- Hydraulic Schematic - Vacuum Fan Motor System
- Wing Down Pressure Schematic (Weight Transfer Mechanism)