Clamp inspection – BAND-IT UL4000-C Cordless Ultra-Lok Tool User Manual
Page 10
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
Document # P08986 Rev. A
© Copyright
BAND-IT-IDEX, Inc. 2012
All rights reserved
www.BAND-IT-IDEX.com
Page 10 of 14
UL4000-C
UL4000-C220
Ultra-Lok Tool
Clamp Inspection
Inspect buckle on completed clamp and tap down buckle shroud.
FRONT VIEW
Completed Free-End Clamp
(Visually inspect lock)
Buckle Shroud
Lock sheared in center
and formed inside
shroud
SIDE VIEW
Completed Free-End
Clamp
Tap down buckle shroud to
complete clamp
Completed clamp
should appear as
shown.
Important: Visually inspect lock formed in band as shown. If lock has slipped under the sheared surface of the
buckle, remove clamp and install a new one at reduced tension by lowering the Drill Clutch torque setting.
Shear Surface
Section View
Good Clamp
Bad Clamp
Lock has slipped back
under sheared buckle
surface
Figure 7
Figure 8
- A92079 Tie-Lok II (4 pages)
- A94079 Ultra-Lok (4 pages)
- A95079 Band-Lok (3 pages)
- Ball-Lok Ties Installation (1 page)
- Ties Installation (1 page)
- Ball-Lok Installation (1 page)
- BT1000 Boss Tool (11 pages)
- C00169 banding (2 pages)
- C00169 Hand Tool (4 pages)
- C00269 JR. Hand Tool (3 pages)
- C00369 Heavy Duty Tool (4 pages)
- C06599 Tension Limiter (2 pages)
- C07569 Bantam Hand Tool (3 pages)
- C08569 Bantam Strapping Hand Tool (4 pages)
- C40099 Ratchet Banding Tool (1 page)
- CB1000 Hand Tool (4 pages)
- D50089/99 Bolted Band Retainer (1 page)
- D51089 (1 page)
- G40269 Giant II Hand Tool (3 pages)
- Gripper Installation (1 page)
- ID200 Series Imprinter (14 pages)
- ID3016 ID Tag Imprinter (1 page)
- ID4002 SS Tape Embosser (2 pages)
- IT0750-AB Mini Tie-Lok Tool (38 pages)
- IT1000-AB 1/4 Tie-Lok Tool (38 pages)
- IT2000-AB 1/4 Junior Tool (38 pages)
- IT3000-AB 1/4 Ultra-Lok Tool (28 pages)
- IT4000-AB 5/16 Band-Lok Tool (28 pages)
- IT5000-AB 3/8 Junior Tool (38 pages)
- IT6000-AB 3/8 Tie-Lok Tool (38 pages)
- J00169 JR. Tool Adapter (2 pages)
- J02069 Pok-It II Tool (2 pages)
- J05069 Heavy Duty Adapter (2 pages)
- J07589/99 Thriftool (2 pages)
- J93099 Cutter Blade Kit (2 pages)
- K50289 Ball-Lok/Self-Lok Tool (5 pages)
- M15650 Scru-Band Kit (1 page)
- M21050 Scru-Seal (1 page)
- M50389 Multi Lok Tool (5 pages)
- Q Band Installation (1 page)
- S03869 Center Punch Tool (2 pages)
- S100 Classic Air Tool (18 pages)
- S35099 Automatic Air Tool (34 pages)
- S75099 Pneumatic Junior Clamp Application Tool (21 pages)
- Shield-Lok SL4099 Tool Pack (15 pages)