Brady 300X-PLUS - Manual (Page 99)

Media Specifications
Media Specifications 300/600X-PLUS 203X-PLUS 360X-PLUS
Minimum label length*
Tear-off 0.7" (18 mm) 0.7" (18 mm) 0.7" (18 mm)
Peel-off 0.5" (13 mm) 0.5" (13 mm) 0.5" (13 mm)
Cutter 1.5" (38 mm) 1.5" (38 mm) 1.5" (38 mm)
Rewind 0.25" (6 mm) 0.25" (6 mm) 0.25" (6 mm)
Total media width
(label + liner, if any)
Minimum 0.79" (20 mm) 1.57” (40 mm) 2.00” (51 mm)
Maximum 3.54" (90 mm) 5.51” (140 mm) 7.1” (180 mm)
Total thickness
(includes liner, if any)
Minimum 0.003” (0.076 mm) 0.003” (0.076 mm) 0.003” (0.076 mm)
Maximum 0.012” (0.305 mm) 0.012” (0.305 mm) 0.012” (0.305 mm)
Cutter maximum full-width media
thickness
.014" (.35 mm) .009" (.23 mm) .007" (.18 mm)
Roll media core inside diameter 3” (76 mm) 3” (76 mm) 3” (76 mm)
Maximum roll diameter 8.0” (203 mm) 8.0” (203 mm) 8.0” (203 mm)
Inter-label gap
Minimum 0.079” (2 mm) 0.079” (2 mm) 0.079” (2 mm)
Preferred 0.118” (3 mm) 0.118” (3 mm) 0.118” (3 mm)
Maximum
Maximum inter-label gap =
2 x (label length for which you have calibrated the printer) + 1”
Maximum internal fanfold media pack size
(label + liner) L x W x H
8.0” x 3.54” x 4.5”
(203x90x114 mm)
8.0” x 5.51” x 4.5”
(203x140x114 mm)
8.0” x 7.1” x 4.5”
(203x180x114 mm)
Ticket/tag sensing notch L x W
0.12" x .25"
(3 mm) x (6 mm)
0.12" x .25"
(3 mm) x (6 mm)
0.12" x .25"
(3 mm) x (6 mm)
Ticket/tag sensing hole diameter 0.125" (3 mm) 0.125" (3 mm) 0.125" (3 mm)
Effective leading edge
registration accuracy*
Vertical ±0.060” (±1.5 mm) ±0.070” (±1.8 mm) ±0.060” (±1.5 mm)
Horizontal ±0.060” (±1.5 mm) ±0.070” (±1.8 mm) ±0.060” (±1.5 mm)
Additional
specs. for
black mark
sensing
Mark length
(measuring
parallel to
label/tag edge)
Minimum 0.12” (3 mm) 0.12” (3 mm) 0.12” (3 mm)
Maximum 0.43” (11 mm) 0.43” (11 mm) 0.43” (11 mm)
Mark width
(measuring
perpendicular to
label/tag edge
Minimum 0.43” (11 mm) 0.43” (11 mm) 0.43” (11 mm)
Maximum Full media width Full media width Full media width
Mark location Marks must be located within .040" (1 mm) of the inside media edge.
Mark density
> 1.0 ODU
(Optical Density Unit)
> 1.0 ODU
(Optical Density Unit)
> 1.0 ODU
(Optical Density Unit)
Maximum density of the back of
the media on which the black
mark is printed
0.5 ODU 0.5 ODU 0.5 ODU
* Media registration and minimum label length are affected by media type and width, ribbon type,
print speed, and printer mode of operation. Performance improves as these factors are optimized.
Brady recommends always qualifying any application with thorough testing.
Brady X-PLUS Series User’s Guide 91