NOVUS Controller N480D - Manual (Page 3)

N480D Controller
NOVUS AUTOMATION 3/6
PROGRAM LEVEL
Ptol
Program
Tolerance
Maximum admitted deviation of PV with respect to SP.
If exceeded, the program execution is suspended (the
internal timer freezes) until the deviation be returns
back within the defined tolerance.
The value 0 (zero) disables the function.
Psp0
Psp9
Program SP
Program SP’s, 0 to 9: Group of 10 values of SP that
define the Ramp and Soak profile segments.
Pt1
Pt9
Program Time
Time intervals of the program segments. It defines
the duration in minutes, of each of the 9 program
segments. Configurable between 0 and 9999
minutes.
Pe1
Pe9
Program
event
Program Segment Alarm (Event Alarm). Parameters
that define the alarm must be activated during the
execution of a certain program segment:
OFF Do not activate alarm in this segment.
A1 Activate alarm 1 when program reaches
this segment.
A2 Activate alarm 2 when program reaches
this segment.
A1A2 Activate alarms 1 and 2 when program
reaches this segment.
The alarms chosen must have its function configured
as “rS”.
rPt.P
Repeat
Program
It determines the number of times the program must
be REPEATED, besides the initial execution.
Configurable between 0 and 9999 times. After the
last execution, all controller outputs are turned off
(RUN = OFF).
INPUT LEVEL
Type
tYPE
INPUT TYPE: Selects the input signal type to be
connected to the process variable input. Refer to
Table 1 for the available options.
This must be the first parameter to be
configured.
Dp.po
Decimal Point
DECIMAL POINT. Defines the decimal point
position.
Vnit
unit
UNIT: Defines the indication unit in Celsius or
Fahrenheit
(
Degrees Celsius (°C);
F Degrees Fahrenheit (°F);
A(t
ACtion
CONTROL ACTION:
re
Reverse action. Generally used for
heating.
Dir Direct action. Generally used for
cooling.
Ovt.a
Ovt.b
Ovt.(
Ovt.d OUTA, OUTB, OUTC and OUTD function:
Off
Output not used
(tr Output defined as control output
AL1 Output defined as alarm output 1
AL2 Output defined as alarm output 2
(.0.20 Output defined as control output 0-20
mA (only for OUTD)
(.4.20 Output defined as control output 4-20
mA (only for OUTD)
spll
SP Low Limit
SETPOINT LOW LIMIT: Selects minimum
adjustment for parameters relative to the SP (SP,
A1SP
, A2SP).
spKl
SP High Limit
SETPOINT HIGH LIMIT: Selects maximum
adjustment for parameters relative to the SP (SP,
A1SP
, A2Sp).
0ffs
OFFSet
OFFSET FOR PV: Parameter that allows to add a
value to PV to generate an indication displacement.
A 1fv
A2fv
Alarm Function
ALARM FUNCTION 1 AND 2: See Table 4 for
description of functions and code to be
programmed in these screens.
Ai ky
A2ky
Alarm
HYsteresis
ALARM HYSTERESIS 1 AND 2: Defines the
difference between the measured value when the
alarm is activated and the value that is deactivated.
A1bl
A2bl
Alarm
Blocking
Initial Alarm block:
Yes
Enables initial block
No Does not enable initial block
Pr.ty
Program Type
Type of program to be adopted by controller:
none
Does not adopt any type of program
rate Adopts ramp to level function
Pr Adopts complete Ramp and Level
program.
CALIBRATION LEVEL
All types of input and output are calibrated at the factory. If recalibration
is required, it must be performed by a specialist. If this cycle is
accessed accidentally, pass through all parameters without making
changes to their values.
pass Password. Input of the Access Password.
This parameter is presented before the protected
cycles. See item Protection of Configuration.
inL( Input Low Calibration. Enter the value
corresponding to the low scale signal applied to the
analog input.
ink( Input High Calibration. Enter the value
corresponding to the full scale signal applied to the
analog input.
0vL( Output Low Calibration. Enter of the value
measured at the analog output.
0vk( Output High Calibration. Enter of the value
measured at the analog output.
rstr Restore. Restores the factory calibration for all input,
analog output and remote SP, disregarding
modifications carried out by the user.
(j Cold Junction. Adjusts the of cold junction
temperature value.
Pas.( Password. Allows defining a new access password,
always different from zero.
Prot Protection. Sets up the Level of Protection. See
Table 2.
TYPE OF ADOPTED PROGRAM
Two forms of program execution are available in the controller. The
Program Type (Pr.Ty) parameter allows user to choose between
Ramp to Level (rate) and a complete Ramp and Level program (Pr).
User can also choose to not execute any type of program (none).
PROGRAMS OF RAMP AND SOAK
Available when the Rate option in the Pr.Ty parameter is selected.
The controller allows the process temperature to vary gradually from an
initial value until a specified final value, determining a Ramp-like behavior.
The initial value of the Ramp will always be the process initial
temperature (PV). The final value will always be the value defined in SP.
User determines the increase (or decrease) speed of the ramp in the
“rAtE” parameter, which defines a temperature variation rate in degrees
per minute. In order to disable the Ramp function, program the value 0.0.
When the SP value is reached, the controller starts to control the
process in SP (level) by an interval of time or indefinitely.
The t SP parameter, adjustable between 0 and 9999 minutes,
determines the level duration. At the end of the level, the control is