American Electric Lighting ARD - Manual

INSTALLATION INSTRUCTIONS
VALIANT SERIES POST TOP LED VERSION
American Electric Lighting a division of Acuity Lighting Group, Inc. Granville, OH
DRAWING NO. A68128 REV -- (FRONT) ©2009 ACUITY LIGHTING GROUP, INC. PART NUMBER 057-71-68128
OPENING & CLOSING THE ACCESS PANEL: OPENING & CLOSING THE ACCESS PANEL:
1. UNSCREW THE FOUR CAPTIVE SCREWS ATTACHING THE 1. UNSCREW THE FOUR CAPTIVE SCREWS ATTACHING THE
BASE COVER TO THE UNIT, TOTALLY DISENGAGING THEM BASE COVER TO THE UNIT, TOTALLY DISENGAGING THEM
FROM THE CASTING. (SEE FIGURE 2). THE SCREWS ARE FROM THE CASTING. (SEE FIGURE 2). THE SCREWS ARE
DISENGAGED WHEN THE SCREWS CAN MOVE FREELY DISENGAGED WHEN THE SCREWS CAN MOVE FREELY
UP AND DOWN. UP AND DOWN.
2. LIFT THE BASE COVER FREE. 2. LIFT THE BASE COVER FREE.
3. TO REINSTALL THE BASE COVER, REPEAT THE STEPS ABOVE 3. TO REINSTALL THE BASE COVER, REPEAT THE STEPS ABOVE
IN REVERSE ORDER. IN REVERSE ORDER.
NOTE: BE SURE THAT THE “SS” EMBOSSMENT ON THE BASE NOTE: BE SURE THAT THE “SS” EMBOSSMENT ON THE BASE
COVER IS ORIENTED WITH THE STREET SIDE OF THE UNIT COVER IS ORIENTED WITH THE STREET SIDE OF THE UNIT
AS DEPICTED. AS DEPICTED.
FULL CUTOFF BASE COVER REMOVAL & INSTALLATION: FULL CUTOFF BASE COVER REMOVAL & INSTALLATION:
11.. TO OPEN THE ACCESS PANEL, LOCATE THE FOUR CLOSURE TO OPEN THE ACCESS PANEL, LOCATE THE FOUR CLOSURE
SCREWS. THESE ARE LOCATED INSIDE THE RING OF LEDs, SCREWS. THESE ARE LOCATED INSIDE THE RING OF LEDs,
MOUNTED IN A PLATE UNDER THE HOOD (SEE FIGURE 1.) MOUNTED IN A PLATE UNDER THE HOOD (SEE FIGURE 1.)
2. LOOSEN THE FOUR CLOSURE SCREWS. T 2. LOOSEN THE FOUR CLOSURE SCREWS. THE SCREWS ARE HE SCREWS ARE
ADEQUATELY LOOSENED WHEN T ADEQUATELY LOOSENED WHEN THE HE ACCESS PANEL ACCESS PANEL CAN CAN
MOVE FREELY UP MOVE FREELY UP AND AND DOWN. DOWN.
3. 3. SLIDE THE ACCESS PANEL OVER TO THE ROUND AREAS SLIDE THE ACCESS PANEL OVER TO THE ROUND AREAS
OF THE KEYHOLE SLOTS, DISENGAGE IT FROM THE OF THE KEYHOLE SLOTS, DISENGAGE IT FROM THE
SCREW HEADS, AND LOWER THE PANEL. IT WILL HANG SCREW HEADS, AND LOWER THE PANEL. IT WILL HANG
SAFELY FROM THE POWER SUPPLY WIRING. SAFELY FROM THE POWER SUPPLY WIRING.
4. TO 4. TO REPLACE REPLACE THE THE PANEL PANEL, SIMPLY , SIMPLY PLACE THE KEYHOLE PLACE THE KEYHOLE
SLOTS OVER THE SCREW HEADS, SLIDE THE PANEL SLOTS OVER THE SCREW HEADS, SLIDE THE PANEL
OVER AND RE-TIGHTEN THE TWO CAPTIVE CLOSURE SCREWS. OVER AND RE-TIGHTEN THE TWO CAPTIVE CLOSURE SCREWS.
CAUTION
! LIFT UNIT OUT OF BOX BY BAG, NOT CUPOLA
DISCONNECT POWER BEFORE SERVICING OR WIRING THE FIXTURE.
HOUSING MUST BE GROUNDED TO REDUCE POTENTIAL OF ELECTRICAL SHOCK
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION
WARNING
!
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. FOR CODE INTERPRETATION,
CONSULT LOCAL CODE AUTHORITY
CAUTION
!
STREE STREETT SIDE VIEW SIDE VIEW
FIGURE 1 FIGURE 1
MAX POLE OD 3” MAX POLE OD 3”
MIN POLE OD 2.375" MIN POLE OD 2.375"
LOWER HOUSING LOWER HOUSING
ACCESS ACCESS
PANEL PANEL
SCREWS (4) SCREWS (4)
CUPOL CUPOLA A CAP CAP
CUPOL CUPOLA A BASE BASE
CUPOL CUPOLA A LENS LENS
HOOD HOOD
LADDER RES LADDER RESTT (2) (2)
-OPTIONAL- -OPTIONAL-
SE SETT SCREWS (3) SCREWS (3)
ADJUS ADJUST T PHO PHOT TOCONTROL OCONTROL
B BY Y LIFTING & TURNING LIFTING & TURNING
CUPOL CUPOLA A SIMU SIMULT LTANEOUS ANEOUSLLY Y
BASE COVER BASE COVER
TM
CAPTIVE CAPTIVE
SCREW FOR SCREW FOR
POWER POWER
PAD (4) PAD (4)
CHIMNEY CHIMNEY
REST REST
CHIMNEY REST CHIMNEY REST
ATTACHMENT ATTACHMENT
SCREW (2) SCREW (2)
DO NOT DO NOT
REMOVE REMOVE
LENS LENS
PPANEL (4) ANEL (4)
"SS" EMBOSSMENT "SS" EMBOSSMENT
FIGURE FIGURE 22
OPEN OPEN HOOD - HOOD - TTOP VIEW OP VIEW
LOWER LOWER
HOUSING HOUSING