American Electric Lighting 125 new User Manual

Warning, Caution

125 SERIES HORIZONTAL LUMINAIRE

INSTALLATION INSTRUCTIONS

American Electric Lighting a division of Acuity Lighting Group, Inc. Conyers, GA

DRAWING NO. B62015 REV C

PART NUMBER 057-71-62015

ADJUSTING SCREW

SOCKET

SOCKET GASKET

REFLECTOR BRACKET

SOCKET BRACKET

NOTE: *Available with coated lamp only

**Requires socket spacer

POLYCARB

175/250W MERC/MH

II MSC

3**

III MSC

400W MERC/MH

DROP LENS

3**

2**

3**

LENS

LAMP

TYPE

VERT

HORZ

III MC

II MC

IV MSC

III MS

II MC

III MSC

II MC

III MSC

II MSC

III MSC

I MSC

II MSC

III MC

II MC

III MSC

II MSC

35-150W HPS

200-400W HPS

175/250W MERC/MH

400W MERC/MH

DROP LENS

FLAT LENS

POLYCARB

175/250W MERC/MH

III MC

3**

TERMINAL BLOCK. VERIFY THAT SUPPLY VOLTAGE IS CORRECT

AS NOTED ON THE TERMINAL BLOCK LABEL. REFER TO THE WIRING

INFORMATION AND RATINGS.

DIAGRAM AND THE DATA ON THE BALLAST FOR CONNECTION

CLEAN OR REPLACE AS DESIRED.

SUPPORT THE REFRACTOR AT ALL TIMES. REMOVE REFRACTOR

HOUSING". ROTATE THE REFRACTOR LATCH BEING CAREFUL TO

OPEN THE LOWER DOOR AS OUTLINED UNDER "REMOVE LOWER

REFRACTOR REPLACEMENT

DETERGENT AND RINSED WITH CLEAN WATER TO MAINTAIN EFFICIENCY.

THE OPTICAL ASSEMBLY SHOULD BE CLEANED WITH A MILD

MAINTANCE AND CLEANING

SOCKET TO ITS NEW LOCATION AND REASSEMBLE.

SOCKET TO THE ADJUSTABLE BRACKET AND MOVE THE

OF THE GASKET. REMOVE THE TWO SCREWS HOLDING THE

SOCKET BRACKET SLIGHTY AND SLIDE THE SOCKET OUT

THE SOCKET SCREWS HOLDING SOCKET. NEXT SPREAD THE

START BY REMOVING THE TWO SOCKET WIRES AND THEN

REMOVAL OF THE SOCKET FROM THE SOCKET BRACKET.

ADJUSTMENT, BUT IF YOU DO IT WILL REQUIRE THE

FOR SETTINGS. YOU SHOULD NOT HAVE TO DO ANY VERTICAL

THE SCREWS. REFER TO TYPE AND DISTRIBUTION CHART

POSITION. THEN SLIDE IT BACK DOWN AND TIGHTEN

1/4" AND SLIDE IT BACK OR FORTH TO THE DESIRED

OF THE SOCKET BRACKET. MOVE THE SOCKET UP ABOUT

LOOSEN THE TWO (DO NOT REMOVE) SCREWS ON EITHER SIDE

SOCKET ADJUSTMENT

AND CONNECT THEM TO THE PROPER TERMINALS ON THE

THEM SO THEY DO NOT INTERFERE WITH ANY COMPONENTS,

FEED THE SUPPLY WIRES THROUGH THE MAST ARM, DRESS

BOLTS TO 10 ft. lbs.

THE FRONT ONES. WHEN THE LUMINAIRE IS LEVEL, TORQUE

HIGH, LOOSEN THE TWO REAR FITTER BOLTS AND TIGHTEN

UNTIL THE LUMINAIRE IS LEVEL. IF THE FRONT END IS

TIGHTEN THE TWO REAR ONES. REPEAT THIS PROCEDURE

IS LOW, LOOSEN THE TWO FRONT FITTER BOLTS AND

MAST ARM UNTIL IT IS LEVEL. IF THE FRONT END

FROM SIDE TO SIDE, TWIST THE LUMINAIRE ON THE

THE LUMINAIRE. IF THE LUMINAIRE IS NOT LEVEL

PLACE A LEVEL ON THE AREA PROVIDED ON TOP OF

BOLTS FINGER TIGHT.

LUMINAIRE ON TO MAST ARM TO STOP AND TIGHTEN

MOUNTING LUMINAIRE ON A 2" MAST ARM. SLIDE

REMOVE CENTER OF BIRD SHIELD IF YOU ARE

1 1/4" MAST ARM & 1 1/4" FOR 2" MAST ARM.

LOOSEN FITTER CLAMP BOLTS. ABOUT 1/2" FOR

MOUNTING/LEVELING

LIFT OFF UPPER HOUSING.

LATCH. ROTATE LOWER HOUSING ABOUT 140í AND

OPEN LOWER HOUSING BY PULLING ON FRONT TRIGGER

REMOVE LOWER HOUSING

FOLD INSULATING BARRIER DOWN

AFTER CONNECTING WIRES

APPLY RTV BETWEEN WEATHER

GUARD AND REAR OF HOUSING

WARNING

DISCONNECT POWER BEFORE RELAMPING OR WIRING THE FIXTURE.

READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION

TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL

AND LOCAL ELECTRICAL/BUILDING CODES. FOR CODE INTERPRETATION, CONSULT LOCAL CODE AUTHORITY

CAUTION