American Electric Lighting 325 new User Manual

Wiring, Socket adjustment, Maintance and cleaning

325 SERIES HORIZONTAL LUMINAIRE

INSTALLATION INSTRUCTIONS

DRAWING NO. B65850 REV A

PART NUMBER 057-71-65850

UPPER HOUSING

TRIGGER LATCH

BEZEL DOOR

REFRACTOR

1/4" SCREW

BALLAST DOOR LATCH

BALLAST DOOR

ADJUSTING SCREW

SOCKET

SOCKET GASKET

REFLECTOR BRACKET

SOCKET BRACKET

LOOSEN THE CAPTIVE 1/4" SCREW.THERE IS ALSO A

BALLAST DOOR LATCH, BUT THIS LATCH IS GRAVITY

ACTUATED AND LATCHES WHEN LUMINAIRE IS MOUNTED

IN ITS OPERATING POSITION. GRASP 1/4" SCREW AND

LIFT BALLAST DOOR UNTIL YOU CAN GET A FIRM GRIP

LOOSEN FITTER CLAMP BOLTS. ABOUT 1/2" FOR

1 1/4" MAST ARM & 1 1/4" FOR 2" MAST ARM.

REMOVE CENTER OF BIRD SHIELD IF YOU ARE

MOUNTING LUMINAIRE ON A 2" MAST ARM. SLIDE

LUMINAIRE ON TO MAST ARM TO STOP AND TIGHTEN

BOLTS FINGER TIGHT.

PLACE A LEVEL ON THE AREA PROVIDED ON TOP OF

THE LUMINAIRE. IF THE LUMINAIRE IS NOT LEVEL

FROM SIDE TO SIDE, TWIST THE LUMINAIRE ON THE

MAST ARM UNTIL IT IS LEVEL. IF THE FRONT END

IS LOW, LOOSEN THE TWO FRONT FITTER BOLTS AND

TIGHTEN THE TWO REAR ONES. REPEAT THIS PROCEDURE

UNTIL THE LUMINAIRE IS LEVEL. IF THE FRONT END IS

HIGH, LOOSEN THE TWO REAR FITTER BOLTS AND TIGHTEN

THE FRONT ONES. WHEN THE LUMINAIRE IS LEVEL, TORQUE

BOLTS TO 10 ft. lbs.

WIRING

FEED THE SUPPLY WIRES THROUGH THE MAST ARM, DRESS

THEM SO THEY DO NOT INTERFERE WITH ANY COMPONENTS,

AND CONNECT THEM TO THE PROPER TERMINALS ON THE

SOCKET ADJUSTMENT

LOOSEN THE TWO (DO NOT REMOVE) SCREWS ON EITHER SIDE

OF THE SOCKET BRACKET. MOVE THE SOCKET UP ABOUT

1/4" AND SLIDE IT BACK OR FORTH TO THE DESIRED

POSITION. THEN SLIDE IT BACK DOWN AND TIGHTEN

THE SCREWS. REFER TO TYPE AND DISTRIBUTION CHART

FOR SETTINGS. YOU SHOULD NOT HAVE TO DO ANY VERTICAL

ADJUSTMENT, BUT IF YOU DO IT WILL REQUIRE THE

REMOVAL OF THE SOCKET FROM THE SOCKET BRACKET.

START BY REMOVING THE TWO SOCKET WIRES AND THEN

THE SOCKET SCREWS HOLDING SOCKET. NEXT SPREAD THE

SOCKET BRACKET SLIGHTY AND SLIDE THE SOCKET OUT

OF THE GASKET. REMOVE THE TWO SCREWS HOLDING THE

SOCKET TO THE ADJUSTABLE BRACKET AND MOVE THE

SOCKET TO ITS NEW LOCATION AND REASSEMBLE.

MAINTANCE AND CLEANING

THE OPTICAL ASSEMBLY SHOULD BE CLEANED WITH A MILD

DETERGENT AND RINSED WITH CLEAN WATER TO MAINTAIN EFFICIENCY.

REFRACTOR REPLACEMENT

OPEN THE LOWER DOOR AS OUTLINED UNDER "REMOVE LOWER

HOUSING". ROTATE THE REFRACTOR LATCH BEING CAREFUL TO

SUPPORT THE REFRACTOR AT ALL TIMES. REMOVE REFRACTOR

CLEAN OR REPLACE AS DESIRED.

DIAGRAM AND THE DATA ON THE BALLAST FOR CONNECTION

INFORMATION AND RATINGS.

AS NOTED ON THE TERMINAL BLOCK LABEL. REFER TO THE WIRING

TERMINAL BLOCK. VERIFY THAT SUPPLY VOLTAGE IS CORRECT

WITH YOUR FREE HAND. BE VERY CAREFUL AS THE BAL-

LAST DOOR IS VERY HEAVY. ROTATE BALLAST ABOUT

140í, REMOVE FROM UPPER HOUSING AND LAY IT DOWN.

DISCONNECT ELECTRICAL CONNECTION BETWEEN UPPER

HOUSING AND BALLAST DOOR.

REMOVE BEZEL DOOR

PULL ON TRIGER LATCH, ROTATE BEZEL DOOR ABOUT

140í AND REMOVE FROM UPPER HOUSING.

REMOVE BALLAST DOOR

MOUNTING/LEVELING

LEVELING

3**

III MSC

175/250W MERC/MH

POLYCARB

FLAT LENS

DROP LENS

400W MERC/MH

175/250W MERC/MH

200-400W HPS

35-150W HPS

II MSC

III MSC

II MC

III MC

II MSC

I MSC

III MSC

II MSC

III MSC

II MC

III MSC

II MC

III MSC

IV MSC

II MC

III MC

HORZ

VERT

TYPE

LAMP

LENS

3**

NOTE: *Available with coated lamp only

**Requires socket spacer

2**

3**

DROP LENS

400W MERC/MH

III MSC