Allied Telesis AT-S88 User Manual

Management software, User’s guide

613-000555 Rev. B

Management
Software

AT-S88

User’s Guide

For the AT-FS750/24POE Fast Ethernet Smart Switch

Version 1.0

Table of contents

Document Outline

Contents
- Figure 1. Main Page 8
- Figure 2. IP Setup Page 12
- Figure 3. Save Configuration Page 13
- Figure 4. Administration Page 15
- Figure 5. Management Page 18
- Figure 6. IP Access List Page 20
- Figure 7. Reboot Page 23
- Figure 8. Save Configuration Page 24
- Figure 9. Physical Interface Page 26
- Figure 10. Bandwidth Control Page 30
- Figure 11. Power over Ethernet Page 36
- Figure 12. Port Diagnosis Example 41
- Figure 13. (SNMP) Community Table Page 46
- Figure 14. (SNMP) Host Table Page 47
- Figure 15. (SNMP) Trap Setting Page 49
- Figure 16. Static Port Trunk Example 52
- Figure 17. Trunking Page 54
- Figure 18. Trunk Ports Selected 54
- Figure 19. Mirroring Page 61
- Figure 20. Ingress Ports Selected 62
- Figure 21. Egress Ports Selected 62
- Figure 22. Port-Based VLAN Page 71
- Figure 23. Port-based VLAN Ports Selected 72
- Figure 24. Tagged VLAN Page 74
- Figure 25. Add Tagged VLAN Page 75
- Figure 26. Tagged VLAN Ports Selected 76
- Figure 27. VLAN Mode Page 78
- Figure 28. Default Port VLAN & CoS Page 86
- Figure 29. CoS Page 88
- Figure 30. IGMP Snooping Page 94
- Figure 31. Point-to-Point Ports 101
- Figure 32. Edge Port 102
- Figure 33. Point-to-Point and Edge Port 102
- Figure 34. VLAN Fragmentation 103
- Figure 35. Spanning Tree Page 104
- Figure 36. Port Access Control Page 113
- Figure 37. Port Access Control Status Page 116
- Figure 38. Dial-In User Page 118
- Figure 39. RADIUS Page 123
- Figure 40. Traffic Comparison Chart Page 127
- Figure 41. Sample Traffic Comparison Chart 130
- Figure 42. Error Group Chart Page 131
- Figure 43. Sample Error Chart 132
- Figure 44. Historical Status Chart 133
- Figure 45. Sample Historical Status Chart 135
- Figure 46. Dynamic Addresses Page 140
- Figure 47. Dynamic MAC Addresses Associated with a Port 141
- Figure 48. Dynamic MAC Addresses Associated with a VLAN ID 141
- Figure 49. Dynamic MAC Addresses Associated with a MAC Address 142
- Figure 50. Static Addresses Page 144
- Figure 51. Firmware Upgrade Page 148
Figures
- Table 1. Default Mappings of IEEE 802.1p Priority Levels to Priority Queues 83
- Table 2. Customized Mappings of IEEE 802.1p Priority Levels to Priority Queues 83
- Table 3. Example of Weighted Round Robin Priority 85
- Table 4. Bridge Priority Value Increments 97
- Table 5. STP Auto Port Costs 98
- Table 6. RSTP Auto Port Costs 98
- Table 7. RSTP Auto Port Trunk Costs 98
- Table 8. Port Priority Value Increments 99
Tables
Preface
- Where to Find Web-based Guides
- Contacting Allied Telesis
Chapter 1
Getting Started
- Starting a Management Session
  - 1. In a web browser address box, enter the following IP address:
- Quitting a Management Session
Chapter 2
Basic Switch Parameters
- Configuring the IP Address, Subnet Mask, and Gateway Address
  - 1. From the main menu, select System > IP Setup.
- Enabling or Disabling DHCP
  - 1. From the main menu, select System > IP Setup.
- Configuring System Administration Information
- Configuring the System Management Information
  - 1. From the main menu, select System > Management.
- Setting Up IP Address Access
- Rebooting the Switch
  - 1. From the main menu, select System > Reboot.
- Returning the AT-S88 Management Software to the Default Values
  - 1. From the main menu, select Save Configuration.
Chapter 3
Port Configuration
- Enabling or Disabling a Port
  - 1. From the main menu, select Physical Interface.
- Setting a Port’s Speed and Duplex Mode
  - 1. From the main menu, select Physical Interface.
- Enabling or Disabling Flow Control
  - 1. From the main menu, select Physical Interface.
- Configuring Bandwidth Control
  - 1. From the main menu, select Bridge > Bandwidth Control.
Chapter 4
Power over Ethernet
- PoE Overview
- Viewing the PoE Status
  - 1. From the main menu, select PoE.
- Setting the Power Management Mode
  - 1. From the main menu, select PoE.
- Allocating Power to the PoE Ports
  - 1. From the main menu, select PoE.
- Diagnosing PoE Port Problems
  - 1. From the main menu, select PoE.
Chapter 5
SNMP
- SNMP Overview
  - Default SNMP Community Strings
- Setting Up the SNMP Community Table
  - 1. From the main menu, select SNMP > Community Table.
- Setting Up the Host Table
  - 1. From the main menu, select SNMP > Host Table.
- Setting Up SNMP Trap Receivers
  - 1. From the main menu, select SNMP > Trap Setting.
Chapter 6
Port Trunking
- Port Trunking Overview
  - Static Port Trunk Overview
- Creating a Port Trunk
  - 1. From the main menu, select Bridge > Trunking.
- Modifying a Trunk
  - 1. From the main menu, select Bridge > Trunking.
- Removing a Trunk
  - 1. From the main menu, select Bridge > Trunking.
Chapter 7
Port Mirroring
- Port Mirroring Overview
- Configuring Port Mirroring
  - 1. From the main menu, select Bridge > Mirroring.
- Modifying a Port Mirror
  - 1. From the main menu, select Bridge > Mirroring.
Chapter 8
VLANs
- VLAN Overview
- Port-based VLAN Overview
- Tagged VLAN Overview
- Creating a Port-Based VLAN
- Creating a Tagged VLAN
- Changing a Port’s VLAN Mode
  - 1. From the main menu, select Bridge > VLAN > VLAN Mode.
Chapter 9
Class of Service (CoS)
- CoS Overview
  - Scheduling
- Configuring CoS
  - 1. From the main menu, select Bridge > Default Port VLAN & COS.
- Mapping CoS Priorities to Egress Queues
  - 1. From the main menu, select Bridge > CoS.
- Specifying the Scheduling Algorithm
  - 1. From the main menu, select Bridge > COS.
Chapter 10
IGMP
- IGMP Snooping Overview
- Enabling or Disabling IGMP Snooping
  - 1. From the main menu, select Bridge > IGMP Snooping.
Chapter 11
STP and RSTP
- STP Overview
- Enabling or Disabling Spanning Tree
  - 1. From the main menu, select Bridge > Spanning Tree.
- Configuring the STP Bridge Settings
  - 1. From the main menu, select Bridge > Spanning Tree.
- Configuring the Spanning Tree Port Settings
  - 1. From the main menu, select Bridge > Spanning Tree.
Chapter 12
Security
- Port-based Network Access Control
- Setting Up a Dial-In User
- RADIUS
  - RADIUS Implementation Guidelines
  - Configuring RADIUS
    - 1. From the main menu, select Security > RADIUS.
Chapter 13
Statistics
- Statistics Overview
- Viewing the Traffic Comparison Statistic
  - 1. From the main menu, select Statistics Chart > Traffic Comparison.
- Viewing the Error Groups
  - 1. From the main menu, select Statistics Chart > Error Group.
- Viewing the Historical Status
  - 1. From the main menu, select Statistics Chart > Historical Status.
Chapter 14
MAC Addresses
- MAC Address Overview
- Working with Dynamic MAC Addresses
  - Displaying the Dynamic MAC Addresses
    - 1. From the main menu, select Bridge > Dynamic Addresses.
  - Changing the Aging Time
    - 1. From the main menu, select Bridge > Dynamic Addresses.
- Working with Static MAC Addresses
Chapter 15
Downloading New Management Software
- Downloading New Management Software
  - 1. From the main menu, select System > Firmware Upgrade.
Index
- A
- B
- C
- D
- E
- F
- H
- I
- M
- P
- Q
- R
- S
- T
- V
- W