Horner APG SmartRail HE599MIX116 - Manual

MAN0936-02-EN Specifications / Installation
__________________________________________________________________________________________________________________________________________________________________
1/3/2011
Page 1 of 1
1
Specifications
Specifications
INPUTS
Number of Channels 2
Input Ranges 4-20mA, 0-20mA, 0-5V, 0-10V
Absolute Max. Inputs ±15V, ±25mA
Resolution 12-Bit (4uA,5uA,1.25mV, 2.5mV
Input Impedance 1MΩ (voltage), 250Ω (current)
Accuracy < ±0.5%
Conversion Time 1mS/ch
OUTPUTS
Number of Channels 2
Output Ranges 0-10V, 4-20mA, 0-20mA
Absolute Max. Outputs ±15V, ±25mA
Resolution 12-Bit (2.5mV, 4uA, 5uA)
Maximum Load >2kΩ (voltage), <510Ω (current)
Accuracy < ±0.5%
Conversion Time 1mS/ch
General Specifications
Isolation Photocoupler (Input/Power)
Backplane Power Consumed 50mA @ 5V
External Power Required 62mA @ 24V (+/-10%)
Terminal Type Screw Type, Removable 11-posn
Optional Spring-clamp Plug HE599TRM011
Storage Temp. -25° to 70° Celsius
Operating Temp. -0° to 55° Celsius
Relative Humidity 5 to 95% Non-condensing
Dimensions WxHxD
20mm x 90mm x 60mm
0.79” x 3.54” x 2.36”
Weight 73g (2.6 oz.)
CE & UL Compliance CE, UL & C-UL
2 Wiring – I/O
3 Configuration DATA
The SmartRail MIX116 features a dip switch on the front of the unit for selecting voltage (0-10V) or
current (4-20mA or 0-20mA) on a per channel basis. In addition to the physical dip switch, Cscape
(9.1 or later) must be used for software configuration as well. The following parameters are
configurable in Cscape for the MIX116:
Cscape Configuration Data – Selectable per channel
Parameter Selections
4-20mA
0-20mA
0-5V
Input/Output Range
0-10V
Hold Last State
Go to Minimum
Go to Mid-range
Hold Last State (Outputs)
Go to Maximum
4
Installation / safety
a. All applicable codes and standards should be followed in the installation of this product.
b. Shielded, twisted-pair wiring should be used for best performance.
c. Shields should be grounded at one end only, preferably at the end providing the best noise
shunting.
d. Use the following wire type or equivalent: Belden 8441.
For detailed installation and a handy checklist that covers panel box layout requirements and
minimum clearances, refer to the hardware manual of the controller you are using.
When found on the product, the following symbols specify:
7
Technical Support
Technical Support at the following locations:
North America:
Tel: 317 916-4274
Fax: 317 639-4279
Web:
http://www.heapg.com
Email: [email protected]
Europe:
Tel: +353-21-4321266
Fax: +353-21-4321826
Web:
http://www.horner-apg.com
Email: [email protected]
MIX116 LED Status Indication
LED 1 LED 2 Meaning (same for both LEDs)
ON = Normal Operation
FLASH = I/O Error
IN OK OUT OK
OFF = No Power or I/O Error
SmartRail
0-10V, 4-20mA Analog Input/Output Module
HE599MIX116
12-Bit Resolution
No part of this publication may be reproduced without the prior agreement and written
permission of Horner APG, Inc. Information in this document is subject to change without
notice.
Warning: Remove power from the OCS controller and any peripheral equipment connected
to this local system before adding or replacing this or any module.
Warning: Consult
user documentation. Warning: Electrical
Shock Hazard.
+ -
24VDC
N.C.
-
CH2
+
-
CH1
+
-
CH2
+
-
CH1
+
CH1
CH2
CH1
CH2
OUTPUT
INPUT
INPUT
OUTPUT
V I
24VDC @ 130mA
External Power
SHIELD GROUNDED
AT ONE END ONLY
+
-
LOOP PWR
+
-
+ -
4-20mA
TRANSMITTER
0-20mA
<510 OHM
LOAD
0-10V
>2k OHM
LOAD
+
-
0-10VDC
+ -
LOAD
+ -
LOAD
Prefer Spring-clamps?
Optional Spring-clamp style plugs are
available as economical wiring accessories.
See specification table for part number(s).
Representative 10-position plug shown.