Horner APG XL10e OCS Model 4 I/O - Manual (Page 3)

MAN0947-01-EN Specifications / Installation
1/6/2011
Page 3 of 3
5 I/O Register Map
Registers Description Registers Description
%I1 to %I24 Digital Inputs %AI1 to %AI4 Analog inputs
%I32 Output Fault %AI5, %AI6 HSC1 Accumulator
%I25 to %I31 Reserved %AI7, %AI8 HSC2 Accumulator
%Q1 to %Q16 Digital outputs %AI9, %AI10 HSC3 Accumulator
%Q17 Clear HSC1 accumulator to 0 %AI11, %AI12 HSC4 Accumulator
%AQ1, %AQ2 PWM1 Duty Cycle
%Q18
Totalizer: Clear HSC2
Quadrature 1-2: Accumulator 1
Reset to max – 1 %AQ3, %AQ4 PWM2 Duty Cycle
%Q19 Clear HSC3 Accumulator to 0 %AQ5, %AQ6 PWM Prescale
%AQ7, %AQ8 PWM Period
%Q20
Totalizer: Clear HSC4
Quadrature 3-4: Accumulator 3
Reset to max – 1 %AQ9 to %AQ14
Analog outputs
(not present on this model)
%Q21 to %Q32 Reserved
6 Safety
7 Technical Support
For assistance and manual updates, contact Technical Support at the following locations:
North America:
(317) 916-4274
www.heapg.com
email:
[email protected]
Europe:
(+) 353-21-4321-266
www.horner-apg.com
email:
[email protected]
This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or Non-hazardous locations only
WARNING – EXPLOSION HAZARD – Substitution of components may impair suitability for Class I, Division 2
AVERTISSEMENT - RISQUE D'EXPLOSION - LA SUBSTITUTION DE COMPOSANTS PEUT RENDRE CE MATERIAL INACCEPTABLE POUR LES EMPLACEMENTS DE
CLASSE 1, DIVISION 2
WARNING – EXPLOSION HAZARD – Do not disconnect equipment unless power has been switched off or the area is known to be non-hazardous.
AVERTISSEMENT - RISQUE D'EXPLOSION - AVANT DE DECONNECTOR L'EQUIPMENT, COUPER LE COURANT OU S'ASSURER QUE L'EMPLACEMENT EST
DESIGNE NON DANGEREUX.
WARNING: To avoid the risk of electric shock or burns, always connect the safety (or earth) ground before making any other connections.
WARNING: To reduce the risk of fire, electrical shock, or physical injury it is strongly recommended to fuse the voltage measurement inputs. Be sure to locate fuses as close to
the source as possible.
WARNING: Replace fuse with the same type and rating to provide protection against risk of fire and shock hazards.
WARNING: In the event of repeated failure, do not replace the fuse again as a repeated failure indicates a defective condition that will not clear by replacing the fuse.
WARNING: Only qualified electrical personnel familiar with the construction and operation of this equipment and the hazards involved should install, adjust, operate, or service
this equipment. Read and understand this manual and other applicable manuals in their entirety before proceeding. Failure to observe this precaution could result in severe
bodily injury or loss of life.
 All applicable codes and standards need to be followed in the installation of this product.
 Adhere to the following safety precautions whenever any type of connection is made to the module:

Connect the safety (earth) ground on the power connector first before making any other connections.
 When connecting to electric circuits or pulse-initiating equipment, open their related breakers.
 Do not make connections to live power lines.
 Make connections to the module first; then connect to the circuit to be monitored.
 Route power wires in a safe manner in accordance with good practice and local codes.
 Wear proper personal protective equipment including safety glasses and insulated gloves when making connections to power circuits.
 Ensure hands, shoes, and floors are dry before making any connection to a power line.
 Make sure the unit is turned OFF before making connection to terminals.
 Make sure all circuits are de-energized before making connections.
 Before each use, inspect all cables for breaks or cracks in the insulation. Replace immediately if defective.
• Use Copper Conductors in Field Wiring Only, 60/75° C
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Warning: Consult
user documentation. Warning: Electrical
Shock Hazard.
When found on the product, the following symbols specify: