Horner APG XLt OCS HE-XT103-10 User Manual
Page 2
PAGE 2
21 AUGUST 2007
MAN0871-02
XLT103-10
Specifications / Installation
Section 3 continued
4
DIP Switches, Wiring and Jumpers
Wire according to the type of inputs / outputs used and select the appropriate jumper
option.
4.1.
I/O Jumper Setting (JP1)
4.2.
DIP Switch Settings (RS-485)
4.3. Wiring
Examples
J1
Orange
XT103-10
Name
I1 IN1
I2 IN2
I3 IN3
I4 IN4
I5 IN5
I6 IN6
I7 IN7
I8 IN8
H1
HSC1 / IN9
H2
HSC2 / IN10
H3
HSC3 / IN11
H4
HSC4 / IN12
A1 Thermistor
1
A2 Thermistor
2
0V Ground
J2
Black
XE103-10
Name
0V Ground
V+ V+
*
NC No
Connect
Q12 OUT12
Q11 OUT11
Q10 OUT10
Q9 OUT9
Q8 OUT8
Q7 OUT7
Q6 OUT6
Q5 OUT5
Q4 OUT4
Q3 OUT3
Q2
OUT2 / PWM2
Q1
OUT1 / PWM1
V+* Supply for Sourcing Outputs
8
1
Pin
MJ1 Pins
MJ2 Pins
8
TXD OUT TXD OUT
7
RXD IN RXD IN
6
0
V Ground 0
V Ground
5
NC
No
Connect
NC
No
Connect
4
RTS OUT TX- OUT
3
CTS IN TX+ OUT
2
RX- /
TX-
IN /
OUT
RX- IN
1
RX+ /
TX+
IN /
OUT
RX+ IN
Note:
The Cscape Module Setup configuration must match
the selected I/O (JP) jumper settings.
I1
0V
001XLE036
12-24VDC
I1
0V
Positive Logic In Negative Logic In
Positive Logic vs. Negative Logic Wiring
The XLE can be wired for Positive Logic inputs or
Negative Logic inputs.
Factory Use
(default – none)
MJ2 Termination
(default – none)
MJ1 Termination
(default – none)
As seen when looking at the top of the XLT unit.
Memory Slot:
Uses Removable Memory for data logging, screen
captures, program loading and recipes.
Horner Part No.: HE-MC1
Serial Communications:
MJ1
: (RS-232 / RS-485) Use for Cscape programming and
Application-Defined Communications.
MJ2:
(RS-232 / RS-485) Use for Application-Defined
Communications.
Location of I/O jumper (JP1)
and wiring connectors
(J1 & J2).
Wiring Specifications
For I/O wiring (discrete), use the
following wire type or equivalent:
Belden 9918, 18 AWG or larger.
For shielded Analog I/O wiring,
use the following wire type or
equivalent: Belden 8441, 18
AWG or larger.
For CAN wiring, use the
following wire type or equivalent:
Belden 3084, 24 AWG or larger.
The DIP Switches are used for
termination of the RS-485 ports. The
XLE is shipped unterminated.
To terminate, select one of the DIP
Switches and configure it based upon
the option that is desired.
Negative Logic
Positive Logic
JP1 Digital DC Inputs
Default
Q1
Q2
Q3
Q4
Q9
Q10
Q11
Q12
Q5
Q6
Q7
Q8
V+
0V
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
10 - 30VDC
Q13
001XLE024
LOAD
XT103-10 J2 Black
Positive Logic
Digital Out
Note:
The wiring examples show
Positive Logic
input wiring.
I1
I2
I3
I4
0V
I5
I6
I7
I8
H1
001XLE061
12-24VDC
A1
A2
H2
H3
H4
T
T
J1
J2
JP1
001XLE060
XT103-10 J1 Orange
Positive Logic
Digital In
001XLE037-R1