CDN WT2 - Wireless Probe Thermometer/Timer EN - Manual (Page 2)

Note: In the following instructions, names of the control
buttons are shown in CAPS. Function information that appears
on the display is shown in BOLD CAPS.
Battery Installation
Batteries are installed. Remove plastic tab to allow
power. Replace battery when LCD becomes dim and
weak or alert level declines.
Note: Do not mix new batteries with old batteries.
A. Base Station
1. Slide the POWER switch on the right side to the
OFF position.
2. Remove battery cover on the back by sliding tab
in the direction of the arrow.
3. Install two 1.5V AAA batteries observing
polarity shown in compartment. A brief alarm
sounds and the display flashes all segments.
4. Replace the battery cover until it clicks shut.
B. Remote
1. Slide the POWER switch on the back to the
OFF position.
2. Lift the pocket clip on the back to access the
battery cover.
3. Remove battery cover on the back by sliding it
in the direction of the arrow.
4. Install two 1.5V AAA batteries observing
polarity shown in compartment.
5. Replace the battery cover until it clicks shut.
Mounting
A. Base Station
1. Stand
a. On the back of the base station, place the
round end of the stand/clip/loop in the
cavity at the bottom with the flat side of
the length of the stand/clip/loop facing the
bottom.
2. Belt Clip
a. On the back of the base station, insert the
round end of the stand/clip/loop in the
larger portion of the clip depression and pull
up to secure. The length of the stand/clip/
loop is positioned downward.
3. Loop
a. On the back of the base station, insert the
round end of the stand/clip/loop in the
larger portion of the clip depression and pull
up to secure. The length of the stand/clip/
loop is positioned upward.
B. Remote
1. Pocket Clip
a. Press top of the clip to expand pocket clip.
2. Magnet
a. Attract magnet on clip to any metal surface
3. Stand
a. Press top of the clip to expand bottom gap
enough to allow hinged wire to fall into stops
on inside of clip.
4. Loop
a. Hang remote on any protrusion through loop
Operating Instructions
A. On/Off
1. Base Station
Slide the POWER switch on the right side of the
base station to turn it on or off.
2. Remote
Slide the POWER switch on the back of the
remote to turn it on or off.
B. Temperature Scale
Press the °C/°F button inside the battery
compartment of the base station to select
temperature reading in Fahrenheit or Celsius.
A beep sounds and °F or °C appears in both the
ALERT TEMP and PROBE TEMP portions of
the display on the base station.
C. Timer Mode
1. Slide the TEMP/TIMER switch on the right
side of the base station to TIMER. The timer
appears in the lower portion of the display.
Note: The timer is only available on the base station.
2. Count Down
a. Press the MIN and/or SEC buttons to enter
the desired time. Press and hold button for
fast advance. The COUNT DOWN icon (t)
appears in the top of the HOURGLASS icon.
b. Press the START/STOP button to start
counting down.
c. Press the START/STOP button to interrupt
the count. Press the START/STOP button
again to resume the count.
d. When the count reaches 00:00, the alarm
sounds 3 beeps per second for 60 seconds
RESYNC
BEEP
VIB ALERT
POWER
ON OFF
Comp
one
nt Design Northwest, Inc.
Po rtland, OR Model W
T2
Made in China
32 to 482°F/0 to 250°C Counts 100 hours by minutes
ALERT STOP
POWER ON OFF
TEMP TIMER
RF
DIRECT Component Design Northwest, Inc. Portland, OR Model WT2 Made in China 32 to 482°F/0 to 250°C Counts 100 hours by minutes START / STOP MIN
MEMORY
CLEAR
MEAT TASTE
SEC