Powering the fan – DAVIS Vantage Pro ISS Fan-Aspirated Add., 2003 & later User Manual
Page 7
Preparing the ISS for Installation
Page 7
Powering the Fan
The Cabled ISS fan is powered by an AC-power adapter. The Wireless ISS fan is
solar-powered and uses batteries for overnight power storage.
Connecting AC Power (Cabled ISS)
1.
Locate the Junction Board on the fan plate (See below).
2.
Connect the AC-power adapter to the +5V connector on the Junction
Board.
3.
Plug the AC-power adapter into an AC outlet.
4.
Check to see that the fan is blowing air in the upward direction.
5.
Unplug the AC power adapter from the AC outlet until you are ready to
mount the ISS.
6.
Secure the AC power cable and sensor cable to the fan plate with the sup-
plied cable clip.
MOTOR
+VSOL
+5V
Fan Connector
AC Power Adapter Connector
(Cabled ISS Only)
Solar Power Connector
(Wireless ISS Only)
SIM Power Cable
(Wireless ISS Only)
Junction Board Connections
#4 x 1/2" Screw
#4 Flat Washer
Cable Clamp
AC-Power Adapter
Cable
Battery
Compartments
(not used in
AC Models)
Fan Motor
Sensor Cable
Fan Plate
Junction
Board
AC Power-Adapter Cable Routing
ISS Fan Rev B.fm Page 7 Thursday, November 14, 2002 4:29 PM
- Envoy8X Getting Started Guide (16 pages)
- Vantage Pro2 Long Range Repeater Installation Addendum (16 pages)
- Wireless Temperature Station (6372) Installation Manual (12 pages)
- Solar Power Kit For Vantage Weather Stations and Envoy8X (8 pages)
- Energy EnviroMonitor: Console (63 pages)
- EZ-Mount Installation (16 pages)
- Gro/Energy/Health Installation (24 pages)
- GroWeather Console (65 pages)
- GroWeather/EnviroMonitor: Systems Installation (24 pages)
- Health EnviroMonitor: Console (60 pages)
- Anemometer (7911, 7914) (8 pages)
- Rain Collector II for GroWeather, EnviroMonitor, Weather Monitor and Wizard (16 pages)
- Sensor - UV for GroWeather or EnviroMonitor (16 pages)
- Solar Radiation Sensor for GroWeather and EnviroMonitor (16 pages)
- Temperatur/Humidity Sensor for GroWeather, EnviroMonitor, & Weather Monitor (12 pages)
- Temperature Sensor/Probe for GroWeather, EnviroMon., Weather Monitor/Wizard (4 pages)
- GroWeatherLink Software (108 pages)
- GroWeatherLink/ET Data Logger (2 pages)
- Short-Range Modem Pair: Perception, GroWeather, EnviroMon., Monitor, Wizard (8 pages)
- Alarm Output Module (16 pages)
- Cable Coupler Kit (4 pages)
- Cable Crimp-Type Splice Connector (4 pages)
- Complete System Shelter (12 pages)
- Fan-Aspirated Radiation Shield (24 pages)
- Grounding Kit (4 pages)
- Interface Cable Adapter Module (8 pages)
- Mounting Pole Kit Installation (4 pages)
- Mounting Tripod Kit (8 pages)
- Multi-purpose Shelter (12 pages)
- Radiation Shield (7714) (16 pages)
- Radio Surge Protector (4 pages)
- Rain Collector Heater (12 pages)
- Rain Collector Shelf: GroWeather, EnviroMonitor, Weather Monitor & Wizard (8 pages)
- Second Solar Panel for EZ-Mount Solar Power Kit (4 pages)
- Sensor Mounting Arm for GroWeather, EnviroMonitor, Weather Monitor & Wizard (16 pages)
- Sensor Tilting Bracket for GroWeather or EnviroMonitor (8 pages)
- Shelter Heaters (12 pages)
- Solar Power Kit for Non-Vantage Pro Stations (16 pages)
- Surge Protector (2 pages)
- Surge Protector Shelter - Large (8 pages)
- Surge Protector Shelter - Small (4 pages)
- Terminal Box for sensors/interface module, communication lines: GroWeather (8 pages)
- WeatherLink for Windows 4.0 (116 pages)
- WeatherLink Getting Started Guide (20 pages)
- WeatherLink Mac OS X Getting Started Guide (16 pages)