KEPCO BIT 232F User Manual

Kepco, Operator’s manual, Model

This manual is related to the following products:

BIT 232

Table of contents

Document Outline

FIGURE 1-1. Remotely Controlled Power Supply Configurations Using Kepco Products
SECTION 1 - INTRODUCTION
1.1 Scope of Manual
1.2 General Description
- TABLE 1-1. Kepco BIT 232, 488 and 4882 Digital Programming Cards
1.3 Specifications, BIT 232/BIT 232-F
1.4 Accessories
- TABLE 1-2. Applicability of BIT Interface Cards to Specific BOP Models
- TABLE 1-3. Specifications, BIT 232 and BIT 232-F
- SECTION 2 - INSTALLATION
2.1 Unpacking and Inspection
2.2 Set Start-up DefaultS
- 2.2.1 Start-up Language Default
- 2.2.2 Set Power Supply Identification Switch
2.3 Installation of BIT Card into the BOP
- FIGURE 2-1. Installation of BIT Card into BOP
- FIGURE 2-2. BIT 232/BIT 232-F Switch and Adjustment Locations
- TABLE 2-1. Power Supply Identification Switch S2 Setting
2.4 Input/OUtput Signals
- TABLE 2-2. Input/Output Pin Assignments
  - FIGURE 2-3. RS 232C Connector
2.5 RS 232 Connections
- SECTION 3 - CALIBRATION
3.1 Equipment Required
3.2 Adjustment of the Bop ±10 Volt Calibration Controls (R31, R32)
3.3 Adjustment of the Ammeter Zero (R50)
- FIGURE 3-1. BOP Power Supply, Internal Calibration Control Locations
3.4 Adjustment Of The Output Voltage Zero (R81)
3.5 Adjustment of the Full Scale Output Voltage (R21)
- TABLE 3-1. BOP Power Supply, Internal Calibration Controls
3.6 Voltage Reading Zero Calibration (R35)
3.7 Voltage Reading Calibration (R19)
3.8 Adjustment of the Output Current Zero (R83)
3.9 Adjustment of the Full Scale Output Current (R22)
3.10 Current Reading Zero Calibration (R36)
- FIGURE 3-2. Current Shunt Connections
3.11 Current Reading Calibration (R20)
- SECTION 4 - OPERATION
4.1 General
4.2 RS232-C Bus Protocol
4.3 RS232 Implementation
4.4 SCPI Programming
- 4.4.1 SCPI Messages
- 4.4.2 Common Commands/Queries
- 4.4.3 SCPI Subsystem Command/Query Structure
  - FIGURE 4-1. Tree Diagram of SCPI Commands Used with BIT 232/BIT 232-F Interface Card
- 4.4.4 Program Message Structure
4.4.4.1 Keyword
- TABLE 4-1. SCPI Command Index
- TABLE 4-2. Rules Governing Shortform Keywords
  - FIGURE 4-2. Message Structure
4.4.4.2 Keyword Separator
4.4.4.3 Query Indicator
4.4.4.4 Data
4.4.4.5 Data Separator
4.4.4.6 Message Unit Separator
4.4.4.7 Root Specifier
4.4.4.8 Message Terminator
- 4.4.5 Understanding The Command Structure
- 4.4.6 Program Message Syntax Summary
4.5 CIIL Programming
4.6 Programming Examples
- APPENDIX A - SCPI COMMON COMMAND/QUERY DEFINITIONS
  - TABLE A-1. SCPI Common Command/query Index
- APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
  - TABLE B-1. SCPI Subsystem Command/query Index
- APPENDIX C - CIIL COMMAND DEFINITIONS
- APPENDIX D - TERMINAL EMULATION PROGRAM
  - TABLE D-1. ROM BIOS Routines to be replaced with equivalent for non-IBM-PC-compatible PC’s
- APPENDIX E - RS232 COMMAND LOOP PROGRAM
  - TABLE E-1. ROM BIOS Routines to be replaced with equivalent for non-IBM-PC-compatible PC’s
- APPENDIX F - C LANGUAGE FUNCTIONS
- APPENDIX G - BASIC LANGUAGE TERMINAL EMULATION