beautypg.com

Technical specifications – GW Instek GOS-652G User Manual

Page 7

background image

⎯ 2 ⎯

2. TECHNICAL SPECIFICATIONS

20MHz OSCILLOSCOPE

35MHz

50MHz OSCILLOSCOPE

MODEL

SPECIFICATIONS

622G

626G

623G

635G

652G

653G

658G

Sensitivity

1mV ~ 5V/DIV, 12 steps in 1-2-5 sequence

Sensitivity accuracy

5mV ~ 5V/DIV:

≤3%, 1mV ~ 2mV/DIV: ≤5% ( 10℃ to 35℃(50℉ to 95℉) )

<< 5 DIV at the center of display>>

Vernier vertical sensitivity

To 1/2.5 or less of panel-indicated value.

5mV~5V/DIV:DC~20MHz (622G,623G,626G)
5mV~5V/DIV:DC~35MHz (635G)
1mV~2mV/DIV:DC~10MHz

5mV~5V/DIV : DC~50MHz,
1mV~2mV/DIV:DC~15MHz

Frequency bandwidth (-3dB)

AC coupling: Low limit frequency 10Hz (With reference to 100kHz, 8DIV. Frequency response with -3dB.)

Rise time

5mV~5V/DIV:

≈ 17.5ns(622G,623G,626G)

5mV~5V/DIV:

≈ 10ns(635G)

1mV~2mV/DIV:

≈ 35ns

5mV~5V/DIV:

≈ 7ns,

1mV~2mV/DIV:

≈ 23ns

Input impedance

1M ohm ±2% // Approx. 25pF

Square wave characteristics

Overshoot :

≤ 5% (At 10mV/DIV range ) << 5 DIV at the center of display>>

Other distortions and other ranges: 5% added to the above value ( 10℃ to 35℃ (50℉ to 95℉) ).

DC balance shift

5mV ~5V/DIV: ±0.5DIV, 1mV ~ 2mV/DIV: ±2.0DIV

Linearity

< ±0.1 DIV of amplitude change when waveform of 2 DIV at graticule center is moved vertically.

Vertical modes

CH1 : CH1 single channel.
CH2 : CH2 single channel.
DUAL

: CHOP/ALT are auto-set by TIME/DIV switch(CHOP:0.5s~5ms/DIV, ALT:2ms~0.1μs/DIV).

When CHOP switch is pushed in, the two traces are displayed in the CHOP mode at all range.

ADD

: CH1 + CH2 algebraic addition.

Chopping repetition frequency

Approx. 250kHz

Input coupling

AC, DC, GND

Maximum input voltage

400V (DC+AC peak), AC: frequency 1kHz or lower.
When set probe switch at 1:1, the maximum effective readout is 40Vpp (14Vrms at sine wave),
or set probe switch at 1:10, the maximum effective readout is 400Vpp(140Vrms at sine wave).

Common mode rejection ratio

50:1 or better at 50kHz sinusoidal wave. (When sensitivities of CH1 and CH2 are set equally)

VERTICAL
AXIS

Isolation between channels

>1000:1 at 50kHz, >30:1 at 20MHz
(622G,623G,626G)
>1000:1 at 50kHz , >30:1 at 35MHz (635G)
(At 5mV/DIV range)

> 1000:1 at 50kHz
> 30:1 at 50MHz

(At 5mV/DIV range)

This manual is related to the following products: