Edwards Signaling Integrity Synchronized Temporal Horn-Strobe - Manual

© 2011 UTC Fire & Security. All rights reserved. 1 / 6 P/N 3100376 • REV 6.0 • ISS 06MAY11
Description
The Integrity Synchronized Temporal Horn-Strobe is a fire
alarm notification appliance designed for indoor or outdoor
walls and ceilings. (The 15 cd strobe is for indoor use only.)
For model numbers, see Table 1; for accessories see Table 2.
Table 1: Models
Description Numbers
15 cd horn-strobe, red [1] 757-5A-T
XLS757-5A- INT-5AT
2452THS-15-R
15 cd horn-strobe, white [1] 757-5A-TW
XLS757-5A-TW INT-5ATW
2452THS-15-W
30 cd horn-strobe, red 757-3A-T
XLS757-3A-T INT-3AT
2452THS-30-R
30 cd horn-strobe, white 757-3A-TW
XLS757-3A-TW INT-3ATW
2452THS-30-W
75 cd horn-strobe, red [2] 757-4A-T
XLS757-4A-T INT-4AT
2452THS-75-R
75 cd horn-strobe, white [2] 757-4A-TW
XLS757-4A-TW INT-4ATW
2452THS-75-W
15/75 cd horn-strobe, red 757-7A-T
XLS757-7A-T INT-7AT
2452THS-15/75-R
15/75 cd horn-strobe, white 757-7A-TW
XLS757-7A-TW INT-7ATW
2452THS-15/75-W
110 cd horn-strobe, red 757-8A-T
XLS757-8A-T INT-8AT
2452THS-110-R
110 cd horn-strobe, white 757-8A-TW
XLS757-8A-TW INT-8ATW
2452THS-110-W
[1] For indoor use only
[2] Not ULC Listed
Table 2: Accessories
Description Numbers
Surface box, red, indoor 757A-SB
XLS757A-SB INT-SB
2459-SMB-R
Surface box, white, indoor 757A-SBW
XLS757A-SBW INT-SBW
2459-SMB-W
Weatherproof box, red,
outdoor 757A-WB
XLS757A-WB INT-WB
2459-WPB-R
Weatherproof box, white,
outdoor 757A-WBW
XLS757A-WBW INT-WBW
2459-WPB-W
Bidirectional mounting frame,
red, indoor 757A-BDF
XLS757A-BDF INT-BDF
2459-BDF-R
Bidirectional mounting frame,
white, indoor 757A-BDFW
XLS757A-BDFW INT-BDFW
2459-BDF-W
The strobe operates on any existing two-wire signal circuit.
There are jumpers for selecting either a temporal or steady
tone, and high or low volume. See Figure 4 for the jumper
locations.
The strobe features an enhanced synchronization circuit to
comply with the latest requirements of UL 1971 Signaling
Devices for the Hearing Impaired and CAN/ULC-S526 Visible
Signal Devices for Fire Alarm Systems, Including Accessories.
Synchronized operation requires a separately installed
synchronization control module. See Table 3 for a list of
compatible synchronization modules.
Table 3: Compatible synchronized models
Description Numbers
Auto-Sync Output Module SIGA-CC1S SIGA-MCC1S
Genesis Signal Master -
Remote Mount ADTG1M-RM
XLSG1M-RM
G1M-RM
BPS-6(10)A MG1M-RM
EG1M-RM
ZG1M-RM
APS-6(10)A
Installation
WARNING: Electrocution hazard. To avoid personal injury or
death from electrocution, remove all sources of power and
allow stored energy to discharge before installing or removing
equipment.
Notes
• Electrical supervision requires the wire run to be broken at
each terminal. Do not loop the signaling circuit field wires
around the terminals.
• To ensure flash synchronization, do not install this
enhanced strobe (identified by a red cd rating on the front
of the unit) in the same field of view as older models
(identified by a black cd rating on the front of the unit).
Install this product in accordance with applicable requirements
in the latest editions of NFPA 72, National Fire Alarm and
Signaling Code, and CSA C22.1 the Canadian Electrical Code,
Part 1, Section 32, CAN/ULC-S524 Installation of Fire Alarm
Systems and in accordance with the local authority having
jurisdiction.
Integrity Synchronized Temporal Horn-Strobe
Installation Sheet