Amana RSS - Manual (Page 35)

OPERATION AND SERVICE PROCEDURES
Electronic Range Control (ERC) (Models w/Two Piece Control)
RC231002 Rev. 3 34
"ON" will appear in the display.
To change the broil setting while the oven is operating
in the broil mode, simply rotate the "TIME/TEMP
SET." knob to change the setting. The ERC will
automatically initiate the new broil function approxi-
mately two (2) seconds after setting the new entry.
To cancel the broil function, simply press the "SET/
CANCEL" button or rotate the "TIME/TEMP. SET"
knob counterclockwise until the three (3) center hori-
zontal segments appear on the temperature display.
The ERC will then automatically cancel the broil
function.
To Set for Self-Clean:
1. Move the door lock lever to the far right or locked
position.
2. Press the "CLEAN" button. "CLEAN" will appear
along with "3:00" in the display indicating a three (3)
hour cleaning time. The ERC will automatically
initiate the clean function approximately two (2) sec-
onds after the "CLEAN" button is pressed. If the door
lock lever is not moved to the locked position prior to
pressing the "CLEAN" button, "DOOR" will be dis-
played and an alarm will sound as a reminder to lock
the door. The "LOCK" light will be displayed approxi-
mately ten (10) to twenty (20) minutes into the clean
cycle and remain on after the completion of the clean
cycle. At the completion of the clean cycle the time
of day will be displayed along with the "LOCK" light.
The "LOCK" light will turn off when the oven tempera-
ture is at a safe level to open the door.
3. Allow the oven to cool approximately twenty (20) to
thirty (30) minutes before trying to move the door lock
lever to the open position. DO NOT FORCE THE
LOCK LEVER. If the door lock will not open, wait five
(5) minutes and try again. NOTE: The "LOCK" light
and actual door latch locking/unlocking temperatures
are not calibrated with each other, i.e., the door lock
may be opened before the "LOCK" light turns off or
vice versa.
To Set for Delayed Self-Clean:
1. Move the door lock lever to the far right or locked
position.
2. Press the "STOP TIME" button. "STOP TIME" and
the current time of day will be displayed.
3. Rotate the "TIME/TEMP. SET" knob clockwise to set
the desired time the oven is to turn off.
4. Press the "CLEAN" button. "DELAY", "CLEAN", and
"TIME" will appear along with "3:00" in the display
indicating a three (3) hour cleaning time. If the door
lock lever is not moved to the lock position prior to
pressing the "CLEAN" button. "DOOR" will be dis-
played and an alarm will sound as a reminder to lock
the door. The ERC will automatically calculate the
start time.
EXAMPLE: If the current time of day is 12:00, to
operate the oven in a clean function which will end at
5:00, (1) lock the oven door, (2) set the stop time for
5:00 and, (3) press the "CLEAN" button. The ERC will
start the cleaning function at 2:00 and turn the oven
off at 5:00.
When the start time is reached, "DELAY" will turn off,
"ON" will appear, and the ERC will initiate the clean
cycle. The "LOCK" indicator will be displayed ap-
proximately 10-20 minutes into the clean cycle and
remain on after the completion of the clean cycle.
When the stop time is reached, the ERC will auto-
matically turn the oven off and the time of day and
"LOCK" will be displayed. "LOCK" will remain dis-
played until the oven temperature is at a safe level to
open the door.
5. Allow the oven to cool approximately twenty (20) to
thirty (30) minutes before trying to move the door lock
lever to open the door. DO NOT FORCE THE LOCK
LEVER. If the door lock will not open, wait five (5)
minutes and try again. NOTE: The "LOCK" light and
actual door latch locking/unlocking temperatures are
not calibrated with each other, i.e., the door lock may
be opened before the "LOCK" light turns off or vice
versa.
To Use Cancel Function:
1. Pressing the "SET/CANCEL" button will cancel all
cooking, cleaning, or timing functions except the
minute timer function. The display will return to the
time of day unless a minute timer operation is present.
2. To display the time of day during a program, press the
"CLOCK" button. The display will return to the time
of day. To view the remaining time on a program after
returning the display to the time of day, simply press
the appropriate function button ("MINUTE TIMER",
"STOP TIME", "COOK TIME", or "CLEAN" button).
The display will then show the remaining program
time.
ELECTRONIC RANGE CONTROL - ERC