Reese 44579 PROFESSIONAL RECEIVER User Manual
Installation instructions
Installation Instructions
Mitsubishi Outlander
(Except Sport)
Part Numbers:
44579
75555
87444
Hitch Shown In Proper Position
Equipment Required:
Wrenches: 17mm, ¾”
Drill Bits: None
Fastener Kit: 75555F
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
Hitch type
Max Gross
Trailer WT (LB)
Max Tongue
WT (LB)
Weight Distributing
4000 (1816 Kg.)
400 (182 Kg.)
Weight Carrying
Ball Mount
4000 (1816 Kg.)
400 (182 Kg.)
Wiring Access Location: SUV3, SUV4
Plastic Fascia
Weldnuts in Vehicle
Frame Rail-Typical
Vehicle Frame
Tow Hook
4
4
4
4
7
7
7
7
8
8
8
8
6
6
6
6
3
3
3
3
5
5
5
5
1.
Lower exhaust by disconnecting (3) rubber exhaust hangers from muffler, (2) at the front and (1) at the rear of the muffler.
Note: If additional clearance is needed, disconnect muffler from exhaust pipe by removing (2) bolts forward of muffler. Retain bolts for re-
installation.
2.
Raise hitch into position, installing fasteners as shown into existing weldnuts in vehicle frame.
3.
Install tube spacer, blocks and ½-13 x 4” lg. hex bolt thru tow hook and into hole in hitch bracket as shown.
Tighten all M10 x 1.25 CL8.8 fasteners with torque wrench to 42 Lb.-Ft. (57 N*M)
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
4.
Raise exhaust back into position by re-connecting rubber exhaust hangers (re-attach muffler to exhaust pipe if removed in step 1).
Tighten all M10 x 1.25 CL8.8 fasteners with torque wrench to 42 Lb.-Ft. (57 N*M)
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
z
2007, 2011 Cequent Performance Products
Sheet 1 of 3
75555N
8-22-11
Rev. C
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
Form: F205 Rev A 5-6-05
2
2
2
2
1
1
1
1
2
2
2
2
1
1
1
1
2
2
2
2
1
1
1
1
1
1
1
1
Qty. (6)
Hex Bolt – M10 x 1.25 x 40mm CL8.8
5
5
5
5
Qty. (1)
Block – 3/8 x 1-1/2 x 3
2
2
2
2
Qty. (6)
Conical Washer – 3/8”
6
6
6
6
Qty. (2)
Block – 3/16 x 1-1/2 x 2
3
3
3
3
Qty. (1)
Tube Spacer
7
7
7
7
Qty. (1)
Lockwasher – ½”
4
4
4
4
Qty. (1)
Hex Bolt – ½-13 x 4.00 GR5
8
8
8
8
Qty. (1)
Hex Nut – ½-13
These fasteners typical
Both sides of Vehicle
6
6
6
6