beautypg.com

Reese 45300 TITAN RECEIVER User Manual

Installation instructions, Kl m k po pq k n, Po p o pq

background image

Installation Instructions

Part Numbers:

45300

z

2010 Cequent Performance Products

Sheet 1 of 6

45300N

8-25-10

Rev. A

j

Qty. (4)

Hex Bolt, M14 x 2.0 x 45mm CL10.9

(coarse thread)

o

Qty. (2)

Hex bolt , 1/2-13 x 2.00 GR 5

k

Qty. (6)

Conical Toothed Washer, 5/8” (black color)

p

Qty. (4)

Conical Toothed Washer, 1/2” (gold color)

l

Qty. (2)

Hex Bolt, M14 x 1.5 x 45mm CL10.9

(fine thread)

q

Qty. (2)

Hex Nut, 1/2”-13

m

Qty. (2)

Spacer, 1/4” X 1-1/2” X 2”

r

Qty. (1)

Attachment bar LH (117535)

n

Qty. (2)

Flange nut, M14 x 1.5 CL10

s

Qty. (1)

Attachment bar RH (117536)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.

Do Not Exceed Lower of Towing Vehicle Manufacturer’s Rating or

Hitch type

Max Gross

Trailer WT (LB)

Max Tongue

WT (LB)

Weight Distributing

18,000 (8172 Kg)

2500 (1135 Kg)

Weight Carrying

Ball Mount

18,000 (8172 Kg)

2000 (908 Kg)

Wiring Access Location: PU3

Form: F205 Rev A 5-6-05

GMC Sierra/Chevrolet Silverado 2500 & 3500 HD Pickups.

(All inc. Regular, Crew, Extended & Dually - 2 & 4WD Long & Short-bed)

GMC Denali HD Crew-Cab Pickup. Short bed trucks requires drilling

Equipment Required: Cable tie provided

Wrenches: 13mm, 19mm, 21mm, 22mm, 3/4”,
7/8”, & 6” Ratchet Extension

Bumper

Other items: Plastic cutting tool,
(short bed as needed. (heat shield)

Hitch Shown In Proper Position

Vehicle

Frame

Bumper

Fascia

Spring shackle

Drill Bits: Short bed – 3/8”, & 9/16” Rotabroach hole
cutting tool - part number 6811 (sold separately) or
carbide drill

Fastener Kit: 45300F

Tighten 1/2”-13 Gr.5 bolts with torque wrench to 75 Lb.-Ft. (102 N*M)

Tighten M14 x 2.0 CL10.9 bolts to 115 Lb.-Ft. (156 N*M)

Tighten M14 x 1.5 CL10.9 bolts to 148 Lb.-Ft. (201 N*M)

Bumper attachment,
14mm weldnuts

Frame attachment

14mm

weldnuts

j

Drilled holes both sides
Short bed only

k

l

m

k

po

pq

k

n

Bumper
attachment
weldnuts

Existing 14mm
bumper bolts

Existing 14mm
bumper bolts.

r

Bumper , exhaust & heat shield not shown

Forward holes

p

o

p

o

pq

Existing 14mm
bumper bolts

One side at a time, remove
side M14 bolts at the outside
end of the frame rail.

r

s

Note: Fasteners typical both sides

j

k

j

j

k

Install attachment bars