beautypg.com

Reese 45299 TITAN RECEIVER User Manual

Installation instructions, Part numbers

background image

Installation Instructions

Dodge 2500/3500 Pickup

Part Numbers:

45299

Hitch Shown In Proper Position

Equipment Required: WOOD BLOCKS

Drill Bits: 9/16”

Wrenches: m16,m18,m21, 3/8”

Tighten M12 hitch fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)

©

2010, 2011 Cequent Performance Products

Sheet 1 of 6

45299N

12-9-11

Rev. B

j

Qty. (4)

HEX NUT

– M14 X 2.00

o

Qty. (2)

BLOCK

– 1-1/2 X 3-1/2 X 1/4”

k

Qty. (4)

CONICAL WASHER

– 5/8”

p

Qty. (4)

HEX NUT

– ½-13 GR 2H

l

Qty. (6)

HEX NUT

– M12 X 1.75

q

Qty. (2)

FISH WIRE

– 1/2”

m

Qty. (14)

CONICAL WASHER

– 1/2”

r

Qty. (4)

HEX BOLT

– M12 X 1.75 X 45mm CL 10.9

n

Qty. (4)

CARRIAGE BOLT

– 1/2”-13 X 1-3/4” GR 8

10

Qty. (3)

BLOCK

– SPACER 1/2 X 1-1/2 X 5-3/4

Tighten M14 and 1/2” fasteners with torque wrench to 100 Lb.-Ft. (136 N*M)

Fastener Kit: 45299F

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry
of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and
wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE
J684.

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Hitch type

Max Gross

Trailer WT (LB)

Max Tongue

WT (LB)

Weight Distributing

18000 (8172 kg)

2500 (1135 kg)

Weight Carrying

Ball Mount

18000 (8172kg)

2000 (908 kg)

Wiring Access Location: PU3, PU4

Form: F205 Rev A 5-6-05

EXISTING
M14 BOLTS

2010 MODEL
EXISTING
BUMPER
CORNER
BRACE

EXISTING
M12 BOLTS

EXISTING M14 HANDLE NUT (03-09 MODEL)

M14 FLANGED NUT (2010 MODEL)

LONG BED
FRAME

SHORT BED
FRAME

DRILL ONE HOLE

DRILL 2
HOLES

BED ATTACHMENT
HOLE

CENTER BUMPER
ATTACHMENT

BUMPER

ATTACHMENT

j

k

l

m

n

p

o

m

Tighten M12 bed fasteners with torque wrench to 85 Lb.-Ft. (115 N*M)

Tighten all M10 fasteners with torque wrench to 42 Lb.-Ft. (57 N*M)

#3

#4

Bumper

FIGURE 1

NOTE;
WITH THIS HITCH INSTALLED
THE STEP BUMPER IS NO LONGER ABLE
TO BE USED AS A TOWING POINT.

!

03-09 MODEL
EXISTING
BUMPER
CORNER
BRACE

(NOT REQUIRED ON 03-09)

2010 – CURRENT

MODEL

ATTACHMENT

2003-09 MODEL

ATTACHMENT

TOP HOLE – BUMPER
ATTACHMENT

VIBRATION DAMPENER

(ON CERTAIN MODELS ONLY)

m

r

10

Must have pick-up chassis
Spring mount (as shown
above the frame).