CONTREX ML-Drive User Manual
CONTREX Sensors
Table of contents
Document Outline
- Table of Contents
- Index
- A
- AC Power (J2 pins 3, 4, 5)..page
- Acceleration Time..page
- Acceleration/Deceleration..page
- Active Scaling Mode..page
- Alarm
- Alarms, grouped..page
- Appendix A..page
- Appendix B..page
- Appendix C..page
- Appendix D..page
- Appendix E..page
- Appendix F..page
- Appendix G..page
- Appendix H..page
- ASCII, Serial Communications Messages..page
- B
- C
- Calibration
- Character Format..page
- Clear/4..page
- Clear/7..page
- Closed Loop..page
- Closed Loop Compensation..page
- Connections, Serial Communications..page
- Control Command Send..page
- Control Mask..page
- Control Parameter Reference List..page
- Control Parameters..page
- CP-01..page
- CP-02..page
- CP-03..page
- CP-04..page
- CP-05..page
- CP-06..page
- CP-10..page
- CP-12..page
- CP-13..page
- CP-14..page
- CP-15..page
- CP-16..page
- CP-17..page
- CP-20..page
- CP-21..page
- CP-30..page
- CP-31..page
- CP-33..page
- CP-34..page
- CP-61..page
- CP-62..page
- CP-64..page
- CP-65..page
- CP-66..page
- CP-67..page
- CP-68..page
- CP-70..page
- CP-71..page
- CP-72..page
- CP-73..page
- CP-74..page
- CP-80..page
- CP-81..page
- CP-98..page
- Control State..page
- Current Limit
- D
- Data Inquiry..page
- Deceleration Time..page
- Dedicated Keys. See Keys: Dedicated
- Derivative..page
- Deviation..page
- Device Address..page
- Diagnostics..page
- Digital Motor Controller..page
- Direct Enable..page
- Direct Mode..page
- Direct Setpoint..page
- Display Mode Follower..page
- Display Test..page
- Drive Enable..page
- Drive Output..page
- E
- F
- G
- H
- I
- J
- J2 pins 1, 2 (Drive Output)..page
- J2 pins 3, 4, 5 (AC Power)..page
- J4 pin 16 (Drive Enable)..page
- J4 pin 17 (Alarm)..page
- J4 pins 1, 2 (I/O Power)..page
- J4 pins 10, 11 (F–Stop)..page
- J4 pins 12, 14 (Master/Follower)..page
- J4 pins 13, 14 (Setpoint Select)..page
- J4 pins 3, 5 (Lead Frequency)..page
- J4 pins 4, 5 (Feedback Frequency)..page
- J4 pins 6, 8 (Run)..page
- J4 pins 7, 8 (Jog)..page
- J4 pins 9, 11 (R–Stop)..page
- Jog..page
- Jog input (J4 pins 7, 8)..page
- Jog Setpoint..page
- K
- L
- M
- M-Host..page
- Master / Follower Input (J4 pins 12, 14)..page
- Master Engineering Units..page
- Master Mode..page
- Master Setpoint 1..page
- Master Setpoint 2..page
- Max RPM Feedback..page
- Max RPM Lead..page
- ML-Drive
- Mode of Operation..page
- Monitor Parameter Reference List..page
- Monitor Parameters..page
- Monitor the Performance of the ML-Drive..page
- Motor
- Mounting the ML-Drive..page
- Multidrop Installation, Serial Communications..page
- O
- Open Loop..page
- Operating State..page
- Operating States
- Operation
- Acceleration/Deceleration..page
- Alarms..page
- Control Parameters..page
- Direct Mode..page
- Follower Mode..page
- Input Monitoring..page
- Inverse Follower Mode..page
- Inverse Master Mode..page
- Jog..page
- Keypad Operation..page
- Logic Control..page
- Logic Inputs..page
- Logic Output..page
- Master Mode..page
- Monitor Parameters..page
- Output Monitoring..page
- Performance Monitoring..page
- Serial Communications..page
- Status Monitoring..page
- Tuning..page
- Output..page
- P
- R
- S
- T
- U
- W
- A