Draw-Tite 118531 T-ONE CONNECTOR - Manual

WARNING
The black box-module is intended to be mounted
ONLY in the INTERIOR of the vehicle. Mounting on
the exterior or areas exposed to the elements or
moisture could cause serious damage to the vehicle
and module. Secure the remainder of the T-Connector
harness with the cable ties provided, to prevent
damage or rattling and being careful to avoid any
areas that would pinch, cut or melt the wire.
WARNING
All connections must be complete for the T-Connector
to function properly. Test and verify installation with a
test light or trailer once installed. For initial test, reset
vehicle electrical system by temporarily removing the
key from the ignition. Re-insert key and turn key to
the proper position.
11. Replace the trunk threshold panel, floor coverings
and felt trunk liner removed during installation.
NOTE
Store 4-Flat in rear cargo area when not in use.
WARNING
Overloading circuit can cause fires. DO NOT exceed
lower of vehicle manufacturer rating or:
• Max. stop/turn light: 2 per side (4.2 amps)
• Max. tail lights: (7.5 amps)
Read vehicle’s owners manual & instruction sheet
for additional information.
118531-037 Rev. A 03/02/11
ENGLISH
TOOls NEEdEd:
Trim Panel Remover, 10mm Socket &
Ratchet or 10mm Wrench, Drill (3/32” Drill Bit),
1/4” Socket, Wire Crimpers, Wire Cutters,
Philips Head Screwdriver, Test-probe
1. Open trunk and remove threshold panel. Partially
remove the corner felt trunk liner, on both sides,
exposing the vehicle’s taillight wiring harness d .
2. On the driver and passenger sides of the vehicle,
locate the vehicle’s taillight wiring harness. The
taillight wiring harness will have a connection point,
on both sides, matching the ends of the T-Connector.
Separate this connector, being careful not to break
the locking tabs. All connector surfaces should be
clean and free of dirt e .
3. On the driver’s side, insert the T-Connector end,
with the yellow wire, between the vehicle wiring
connectors and lock into place. Be careful not to
damage the locking tabs and be sure that connectors
are fully inserted with locking tabs in place.
4. Route the T-Connector end, with the green wire,
under felt trunk liner to passenger side vehicle
taillight wiring harness.
Repeat step 3 for the passenger’s side using the
T-Connector containing the green wire.
5. Locate a suitable grounding point on the driver’s side
near the connectors. Drill a 3/32” hole and secure
white wire with eyelet using screw provided. Do not
drill into any exposed surfaces.
CAUTION
Verify what is behind any surface prior to drilling to
avoid damage to the vehicle and/or personal injury.
Do not drill into any exposed surfaces.
6. On the driver’s side, locate the red 12 ga.
Power wire from the T-Connector. Attach the
black 12 ga. wire provided.
Route the black wire along the exterior frame or
follow the existing wiring along the thresholds into
the engine compartment up to the battery avoiding
areas that may pinch or break the wire f .
7. Disconnect the vehicle’s Negative (-) battery cable.
If not removed, remove the fuse from the yellow fuse
holder (provided). After cutting the fuse holder wire,
attach the ring terminal and secure to the vehicle’s
Positive (+) battery cable. Connect the other end of
the fuse holder to the black 12 ga. wire, using the
yellow butt connector (provided) gh .
WARNING
Read and follow all warnings and cautions printed
on the tow vehicle’s battery.
8. Reconnect the vehicle’s Negative (-) battery cable
and install the 15 amp fuse into the fuse holder
from step 7.
9. Locate the T-Connector’s Grey 12-Pin connector
and insert it into the mating connector located
on the black box-module. Check to see that the
mating surfaces of the wiring connectors match.
All connector surfaces should be clean and free of
dirt. Be careful not to damage the locking tabs and
be sure that connectors are fully inserted with
locking tabs in place i .
10. Locate a flat surface in an out of the way place
and mount the T-Connector’s black box-module,
to prevent damage or rattling.
NOTE
This surface should be in an area that is free of
any moisture and mounted in an area that it is high
enough where it could not be exposed to direct
contact with any water or liquid substance.
Jetta sedan
REAd THIs FIRsT:
Read and follow all vehicle warnings and installation
instructions before beginning installation. Wear safety
glasses and use all safety precautions during installation.
lIsEz CECI EN PREmIER:
Lire et observer toutes les consignes de sécurité et les
instructions avant de commencer l’installation. Durant
l’installation, veiller à toujours porter des lunettes de
protection et respecter les mesures de sécurité.
lEA EsTO PRImERO:
Lea y siga todas las advertencias e instrucciones de
instalación del vehículo antes de empezar la instalación.
Use gafas de seguridad y todas las precauciones de
seguridad durante la instalación.
Installation Instructions
directives de montage
Instrucciones de Instalación
T-Connector
Connecteur en T
Conector en T
d
f
e
g
h
i