beautypg.com

Draw-Tite 118538 T-ONE CONNECTOR User Manual

Draw-Tite For the car

background image

10. Reconnect the vehicle’s Negative (-) battery cable

and install the 10 amp fuse into the fuse holder

from step 9.

WARNING

All connections must be complete for the T-Connector

to function properly. Test and verify installation with a

test light or trailer once installed. For initial test, reset

vehicle electrical system by temporarily removing the

key from the ignition.

11. Secure the remainder of the T-Connector harness

with the cable ties provided, to prevent damage or

rattling and being careful to avoid any areas that

would pinch, cut or melt the wire.

12. Reinstall the plastic trim panels, threshold,

cargo trays, tail lamps and other items removed

during installation, being careful not to pinch or

cut the wires.

NOTE

Store 4-Flat connector in rear cargo area when

not in use.

WARNING

Overloading circuit can cause fires. DO NOT exceed

lower of towing manufacturer rating or:

• Max. stop/turn light: 1 per side (2.1 amps)

• Max. tail lights: (5.6 amps)

Read vehicle’s owners manual & instruction sheet

for additional information.

118531-037

Rev. A

03/02/11

ENGLISH

TOOls NEEdEd:

Trim Panel Remover, 10mm Socket &

Ratchet or 10mm Wrench, Drill (3/32” Drill Bit),

1/4” socket, Wire Crimpers, Wire Cutters,

Philips Head Screwdriver, Test-probe

1. Open the rear tailgate to access the bolts that

hold the taillights in place. Using a Phillips head

screwdriver, Remove the taillights on both the

driver and passenger side of the vehicle. After

removing the screws, carefully pull the taillight

away from the vehicle being careful not to

damage the alignment pins

de

.

2. Pull away the grommets on both Driver’s and

Passenger sides to access the interior area of

the vehicle.

On the driver and passenger sides of the vehicle,

locate the vehicle’s taillight wiring harness. The

taillight wiring harness will have a connection point,

on both sides, matching the ends of the T-Connector.

Separate this connector, being careful not to break

the locking tabs. All connector surfaces should be

clean and free of dirt

f

.

3. Inside the vehicle’s rear cargo area, temporarily

remove all floor coverings, cargo trays and plastic

threshold cover.

Partially remove the rear interior trim panels on both

the driver and passenger side of the vehicle. Several

trim panel fasteners will need to be removed to

remove the panels. Set aside all items removed

being careful not to damage parts.

4. From inside the rear cargo compartment, route the

T-connector with yellow & brown wires thru the

grommet on the driver’s side.

5. On the driver’s side, insert the T-Connector end,

with the yellow wire, between the vehicle wiring

connectors and lock into place. Be careful not

to damage the locking tabs and be sure that

connectors are fully inserted with locking tabs

in place. Reseat grommet.

6. Route the T-Connector end with green wire to the

passenger ‘s side behind the panels and along the

threshold. Repeat steps 4 & 5 for T-Connector end

with the green wire.

7. Locate a suitable grounding point on the driver’s side

near the connectors. Drill a 3/32” hole and secure

white wire with eyelet using screw provided. Do not

drill into any exposed surfaces.

CAUTION

Verify what is behind any surface prior to drilling to

avoid damage to the vehicle and/or personal injury.

Do not drill into any exposed surfaces.

8. On the driver’s side, locate the red 12 ga. Power wire

from the T-Connector box. Attach the black 12 ga.

wire provided.

Route the remaining wire through the opening in the

taillight socket, behind the bumper.

Route the black wire along the exterior frame or

follow the existing wiring along the thresholds into

the engine compartment up to the battery avoiding

areas that may pinch or break the wiret

g

.

9. Disconnect the vehicle’s Negative (-) battery cable.

If not removed, remove the fuse from the yellow

fuse holder (provided). After cutting the fuse

holder wire, attach the ring terminal and secure to

the vehicle’s Positive (+) battery cable

hi

. Connect

the other end of the fuse holder to the black 12 ga.

wire, using the yellow butt connector (provided).

WARNING

Read and follow all warnings and cautions printed

on the tow vehicle’s battery.

Mitsubishi Outlander sport

REAd THIs FIRsT:

Read and follow all vehicle warnings and installation

instructions before beginning installation. Wear safety

glasses and use all safety precautions during installation.
lIsEz CECI EN PREMIER:

Lire et observer toutes les consignes de sécurité et les

instructions avant de commencer l’installation. Durant

l’installation, veiller à toujours porter des lunettes de

protection et respecter les mesures de sécurité.
lEA EsTO PRIMERO:

Lea y siga todas las advertencias e instrucciones de

instalación del vehículo antes de empezar la instalación.

Use gafas de seguridad y todas las precauciones de

seguridad durante la instalación.

Installation Instructions

directives de Montage

Instrucciones de Instalación

T-Connector

Connecteur en T

Conector en T

d

f

e

h

i

g