beautypg.com

Draw-Tite 118609 T-ONE CONNECTOR User Manual

Ef g h d, English, T-connector t-one

background image

WARNING

All connections must be complete for the

T-One

®

T-Connector to function properly.

Test and verify installation with a test light

or trailer once installed. For initial test,

reset vehicle electrical system by temporarily

removing the key from the ignition.

9. Locate a flat surface in an out of the way place

and mount the T-One

®

T-Connector’s black

box-module, to prevent damage or rattling.

10. Secure the remainder of the T-One

®

T-Connector harness with the cable ties

provided, to prevent damage or rattling

and being careful to avoid any areas that

would pinch, cut or melt the wire.

11. Replace carpet, and any other clips or

panels that were removed during installation

being careful not to cut or pinch the wires.

NOTE

Store 4-Flat in trunk area when not in use.

WARNING

Overloading circuit can cause fires. DO NOT

exceed lower of towing manufacturer rating or:

• Max. stop/turn light: 1 per side (2.1 amps)

• Max. tail lights: (5.6 amps)

Read vehicle’s owners manual & instruction

sheet for additional information.

ENGLISH

TOOLS REQUIRED:

Trim Panel Remover, Drill (3/32” Drill Bit),

Philips Head Screwdriver, Test-probe

1. Open trunk. Temporarily remove the rear

threshold plate. Partially remove the felt

trunk liner behind the taillights d.

2. On the driver and passenger sides of the

vehicle, locate the vehicle’s taillight wiring

harness. The taillight wiring harness will have

a connection point, on both sides, matching

the ends of the T-One

®

T-Connector. Separate

this connector, being careful not to break the

locking tabs. All connector surfaces should be

clean and free of dirt e.

3. On the driver’s side, insert the T-One

®

T-Connector end, with the yellow wire,

between the vehicle wiring connectors and

lock into place. Be careful not to damage the

locking tabs and be sure that connectors are

fully inserted with locking tabs in place.

4. Route the T-One

®

T-Connector end with

green wire to the passenger ‘s side behind the

panels and along the threshold. Repeat step

3 using the T-Connector ends containing the

green wire.

5. Locate a suitable grounding point near

the connector. Clean dirt and rustproofing

from the area. Drill a 3/32” hole and secure

the white wire using the eyelet and

screw provided.

CAUTION

Verify what is behind any surface prior to

drilling to avoid damage to the vehicle and/

or personal injury. Do not drill into any

exposed surfaces.

6. From inside the vehicle, connect the black

12 ga. wire and the red wire from the T-One

®

T-Connector black box with the supplied

yellow butt connector. Either route the black

wire thru a grommet and along the exterior

frame or follow the existing wiring along the

thresholds into the engine compartment up to

the battery avoiding areas that may pinch or

break the wire f.

WARNING

If routing the wire thru a grommet and along

the exterior of the vehicle, be careful to avoid

any hot pipes, heat shields, the fuel tank or any

other points that may pinch or break the wire.

7. Disconnect the vehicle’s Negative (-)

battery cable. If not removed, remove

the fuse from the yellow fuse holder

(provided). After cutting the fuse holder

wire g, attach the ring terminal and secure

to the vehicle’s Positive (+) battery cable.

Connect the other end of the fuse holder to

the black 12 ga. wire, using the yellow butt

connector (provided) h.

WARNING

Read and follow all warnings and cautions

printed on the tow vehicle’s battery.

8. Reconnect the vehicle’s Negative (-) battery

cable and install the 10 amp fuse into the fuse

holder from step 7.

Installation Instructions

Directives de Montage

Instrucciones de Instalación

T-One

®

T-Connector

T-One

®

Connecteur en T

T-One

®

Conector en T

Lexus IS 250 / IS 350

118609-037

Rev. A

10/8/2013

READ THIS FIRST:

Read and follow all vehicle warnings and installation

instructions before beginning installation. Wear safety

glasses and use all safety precautions during installation.
LISEz CECI EN PREMIER:

Lire et observer toutes les consignes de sécurité et les

instructions avant de commencer l’installation. Durant

l’installation, veiller à toujours porter des lunettes de

protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:

Lea y siga todas las advertencias e instrucciones de

instalación del vehículo antes de empezar la instalación.

Use gafas de seguridad y todas las precauciones de

seguridad durante la instalación.

PAGE 1 OF 3

e

f

g

h

d