Draw-Tite 118605 T-ONE CONNECTOR - Manual

WARNING
Test and verify installation with a test light
or trailer once installed.
10. On driver’s side, locate a flat surface in an
out of the way place and mount the T-One ®
T-Connector’s black convertor box with the
double sided tape.
WARNING
Make sure module is mounted so that the
epoxy side of the module is pointed towards
the ground to prevent any water buildup.
11. Reinstall the taillight housing assemblies,
positioning the vehicle wiring harness between
the housing and the vehicle body. Secure the
remainder of the T-One ® T-Connector harness
under the bumper with cable ties provided,
being careful to avoid any areas that would
cut or pinch the wire.
NOTE
Mount 4-Flat in a suitable location under the
vehicle. Bracket not included.
WARNING
Overloading circuit can cause fires. DO NOT
exceed lower of towing manufacturer rating or:
• Max. stop/turn light: 2 per side (4.2 amps)
• Max. tail lights: (7.5 amps)
Read vehicle’s owners manual & instruction
sheet for additional information.
ENGLISH
TOOLS REQUIRED:
T30 Socket & Ratchet, Trim Panel Remover,
10mm Socket & Ratchet or 10mm Wrench,
Drill (3/32” Drill Bit), 1/4” Socket,
Wire Crimpers, Wire Cutters, Philips Head,
Screwdriver, Test-probe
1. Open the tailgate and remove the vehicle’s
taillight assemblies by removing the four T30
bolts on each side. Carefully pry the housings
away from the vehicle, being careful not to
break the alignment tabs d.
2. Disconnect the vehicle wiring harness from
both taillight sockets. On the Drivers side,
fish the T-One ® T-Connector end with the
yellow wires up between the bumper and
vehicle body into the taillight pocket e.
3. Plug the T-One ® T-Connector end with the
yellow wire in-between the mating plugs on
the Driver’s side taillight socket and vehicle
wiring harness.
4. Route the T-One ® T-Connector end with green
wire to the passenger’s side and route the
4-Flat underneath the bumper. Route T-One ®
T-Connector end with green wire up through
the opening on the passenger side, being
careful to avoid any hot pipes, heat shields,
the fuel tank or any other points that may
pinch or brake the wire. Repeat step 3.
5. Locate a suitable grounding point near the
connector. (Do not drill into vehicle floor or
bed.) Clean dirt and rustproofing from area.
Drill a 3/32” hole and secure white wire
using eyelet and screw provided.
CAUTION
Verify what is behind any surface prior to
drilling to avoid damage to the vehicle and/
or personal injury. Do not drill into any
exposed surfaces.
6. Disconnect the vehicle’s Negative (-) battery
cable. If not removed, remove the fuse from
the yellow fuse holder (provided). After cutting
the fuse holder wire f, attach the ring
terminal and secure to the vehicle’s Positive
(+) battery cable g. Connect the other end
of the fuse holder to the black 12 ga. wire,
using the yellow butt connector (provided).
WARNING
Read and follow all warnings and cautions
printed on the tow vehicle’s battery.
7. Beginning from the front of the vehicle,
route the black 12 ga. wire rearward along
the frame rail h.
WARNING
Route the wire being careful to avoid any hot
pipes, heat shields, the fuel tank or any other
points that may pinch or break the wire.
8. Route the black 12 ga. wire to the rear driver’s
side. Locate the opening between the vehicle
rear bumper and body allowing entry to the
rear driver’s side taillight area. Route the wire
up through this hole and attach the black
12 ga. wire to the black wire from the T-One ®
T-Connector black box with the supplied
yellow butt connector.
9. Reconnect the vehicle’s Negative (-) battery
cable and install the 15 amp fuse into the fuse
holder from step 5.
Installation Instructions
Directives de Montage
Instrucciones de Instalación
T-One ® T-Connector
T-One ® Connecteur en T
T-One ® Conector en T
Jeep Cherokee
118605-037 Rev. A 8/12/2013
READ THIS FIRST:
Read and follow all vehicle warnings and installation
instructions before beginning installation. Wear safety
glasses and use all safety precautions during installation.
LISEz CECI EN PREMIER:
Lire et observer toutes les consignes de sécurité et les
instructions avant de commencer l’installation. Durant
l’installation, veiller à toujours porter des lunettes de
protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:
Lea y siga todas las advertencias e instrucciones de
instalación del vehículo antes de empezar la instalación.
Use gafas de seguridad y todas las precauciones de
seguridad durante la instalación.
PAGE 1 OF 3
h
f
g
e
d