beautypg.com

Draw-Tite 118554 T-ONE CONNECTOR User Manual

Draw-Tite For the car

background image

8. Reconnect the vehicle’s Negative (-) battery

cable and install the 10 amp fuse into the fuse
holder from step 5.

WARNING
All connections must be complete for the
T-Connector to function properly. Test and
verify installation with a test light or trailer
once installed.

9. On driver’s side, locate a flat surface in

an out of the way place and mount the
T-Connector’s black convertor box with
the double sided tape

k

.

WARNING

Make sure module is mounted so that the

epoxy side of the module is pointed towards
the ground to prevent any water buildup.

10. Reinstall the taillight housing assemblies,

positioning the vehicle wiring harness between
the housing and the vehicle body. Secure the
remainder of the T-Connector harness under the
bumper with cable ties provided, being careful to
avoid any areas that would cut or pinch the wire.

NOTE
Mount 4-Flat in a suitable location under
the vehicle. Bracket not included.

WARNING
Overloading circuit can cause fires. DO NOT
exceed lower of towing manufacturer rating or:
• Max. stop/turn light: 2 per side (4.2 amps)
• Max. tail lights: (7.5 amps)
Read vehicle’s owners manual &
instruction sheet for additional information.

ENGLISH

TOOLS REQUIRED:

Drill (3/32” Drill Bit), Philips Head Screwdriver,
Trim Panel Remover, Wire Crimpers,
Wire Cutters, Test-probe

1. Open the tailgate and remove the vehicle’s

right side taillight assembly by removing the
two clips holding the taillight in place

de

.

Carefully pry the housings away from the
vehicle, being careful not to break the
alignment tabs. Repeat for the vehicle’s
left side taillight assembly.

2. Disconnect the vehicle wiring harness from both

taillight sockets. Plug the T-Connector end with
the yellow wire in-between the mating plugs
on the Driver’s side taillight socket and vehicle
wiring harness

f

.

3. On the Driver’s side, route the T-Connector

end with the green wire and the wire with the
4-Flat connector down through the opening
between the vehicle bumper and body

g

.

Route the T-Connector end with green wire
to the passenger’s side and route the 4-Flat
underneath the bumper. Route T-Connector
end with green wire up through the opening
on the passenger side, being careful to avoid
any hot pipes, heat shields, the fuel tank or any
other points that may pinch or brake the wire.
Repeat step 2.

4. Locate a suitable grounding point near the

connector. (Do not drill into vehicle floor or

bed.) Clean dirt and rustproofing from area.

Drill a 3/32” hole and secure white wire using

eyelet and screw provided.

CAUTION

Verify what is behind any surface prior to drilling

to avoid damage to the vehicle and/or personal

injury. Do not drill into any exposed surfaces.

5. Disconnect the vehicle’s Negative (-) battery

cable. If not removed, remove the fuse from the

yellow fuse holder (provided). After cutting the

fuse holder wire,

h

attach the ring terminal

and secure to the vehicle’s Positive (+) battery

cable

i

. Connect the other end of the fuse

holder to the black 12 ga. wire, using the

yellow butt connector (provided).

WARNING

Read and follow all warnings and cautions

printed on the tow vehicle’s battery.

6. Beginning from the front of the vehicle,

route the black 12 ga. wire rearward along

the frame rail

j

.

WARNING

Route the wire being careful to avoid any hot

pipes, heat shields, the fuel tank or any other

points that may pinch or break the wire.

7. Route the black 12 ga. wire to the rear driver’s

side. Locate the opening between the vehicle

rear bumper and body allowing entry to the rear

driver’s side taillight area. Route the wire up

through this hole and attach the black 12 ga.

wire to the black wire from the T-Connector black

box with the supplied yellow butt connector.

READ THIS FIRST:

Read and follow all vehicle warnings and

installation instructions before beginning installation.

Wear safety glasses and use all safety precautions

during installation.
LISEz CECI EN PREmIER:

Lire et observer toutes les consignes de sécurité et les

instructions avant de commencer l’installation. Durant

l’installation, veiller à toujours porter des lunettes

de protection et respecter les mesures de sécurité.
LEA ESTO PRImERO:

Lea y siga todas las advertencias e instrucciones

de instalación del vehículo antes de empezar la

instalación. Use gafas de seguridad y todas las

precauciones de seguridad durante la instalación.

118554-037

Rev. A

10/31/2011

Installation Instructions

Directives de montage

Instrucciones de Instalación

T-Connector

Connecteur en T

Conector en T

Dodge Nitro / Jeep Liberty

d

e

j

f

g

i

h

k