beautypg.com

Draw-Tite 118402 T-ONE CONNECTOR User Manual

Draw-Tite For the car

background image

5. Locate a suitab

le grounding point near the

connector such as the vehicle's frame or cross
member. (Do not drill into vehicle floor or bed.)
Clean dirt and rustproofing from area. Drill a
3/32" hole and secure

white wire using e

yelet

and screw provided.

CA

UTION

V

erify what is behind any surface prior to drilling to

avoid damage to the vehicle and/or personal injury.
Do not drill into any exposed surfaces.

6. Disconnect the v

ehicle's Negative (-) battery cable.

If not removed, remove the fuse from the yellow
fuse holder (provided). After cutting the fuse holder
wire, attach the ring terminal and secure to the
vehicle's Positive (+) battery cable

k

-

l

.

Connect

the other end of the fuse holder to the

b

lack

12 ga.

wire, using the yellow butt connector (provided).

7. Beginning from the front of the v

ehicle, route the

b

lack

12 ga.

wire rearward along the frame rail.

W

ARNING

Route the wire being careful to a

void any hot

pipes, heat shields, the fuel tank or any other
points that may pinch or break the wire.

8. Contin

uing on as illustrated, route the

b

lack

12 ga.

wire to the rear driver's side

m

.

Locate the opening

between the vehicle rear bumper and body allowing
entry to the rear driver’s side taillight area. Route
the wire up through this hole and attach the

b

lack

12 ga.

wire to the

red wire from the

T-Connector

black box with the supplied yellow butt connector.

9. Reconnect the v

ehicle's Negative (-) battery cable

and install the 10 amp fuse into the fuse holder
from step 6.

W

ARNING

All connections m

ust be complete for the

T-Connector to function properly. Test and verify
installation with a test light or trailer once installed.

10. Secure all loose wir

ing. Behind the vehicle

taillight housing assembly on the driver’s side,
clean a flat area using a mixture of rubbing
alcohol and water. Mount the T-connector
black box using double-sided tape provided.

11. Reinstall the taillight housing assemb

lies,

positioning the vehicle wiring harness between
the housing and the vehicle body. Secure the
remainder of the T-Connector harness with the
cable ties provided, to prevent damage or rattling
and being careful to avoid any areas that would
cut or pinch the wire.

NO

TE:

Mount 4-Flat in a suitab

le location under

the vehicle. Bracket not included.

W

ARNING

Ov

erloading circuit can cause fires. DO NOT

exceed lower of towing manufacturer rating or:
• Max. stop/turn light: 1 per side (2.1 amps)
• Max. tail lights: (5.6 amps)
Read vehicle's owners manual &
instruction sheet for additional information.

Installation Instr

uctions

Directives de Montage

Instrucciones de Instalación

T-Connector

Connecteur en T

Conector en T

18402-037

Rev. A

04/20/05

ENGLISH

TOOLS REQUIRED:

13mm Soc

ket & Ratchet or 13mm Wrench,

Drill (3/32" Drill Bit), Philips Head Screwdriver
Pliers, Trim Panel Remover, Wire Crimpers,
Wire Cutters

1. Open the tailgate to remo

ve the vehicle's taillight

housing assemblies. On the driver’s side, start by
removing the two clips holding the taillight in place

d

.

Inside the vehicle behind the taillights, remove

plastic cover and pull back insulation liner to access
the plastic wing nut holding the taillight in place

e

-

f

-

g

.

Unscrew the plastic wing nut and carefully

pry the vehicle taillight housing assembly away from
the vehicle, being careful not to break the alignment
tabs. Repeat this step for the vehicle’s passenger’s
side taillight assembly.

2. On the dr

iver’s side, disconnect the vehicle

wiring harness from the taillight socket

h

.

Plug the

T-Connector end with the

y

ellow

wire in-betw

een

the mating plugs on the driver’s side taillight
socket and vehicle wiring harness.

3. On the dr

iver’s side, route the T-Connector end

with the

green wire and the wire with the 4-Flat

connector down through the opening between
the vehicle bumper and body

i

-

j

.

4. Route the

T-Connector end with

green wire to the

passenger’s side and route the 4-Flat underneath
the bumper.

W

ARNING

Route the wire being careful to a

void any hot pipes,

heat shields, the fuel tank or any other points that
may pinch or break the wire.

Route T-Connector end with

green wire up through

the opening on the passenger side, being careful to
avoid areas that could damage wiring. Repeat step
2 for T-Connector end with the

green wire

.

READ

THIS FIRST:

Read and f

ollow all instructions carefully

before beginning installation.

LISEZ CECI EN PREMIER:
Lire et suivre toutes les instr

uctions

attenrivement avant le montage.

LEA

ESTO PRIMERO:

Lea y siga todas las instr

ucciones cuida-

dosamente antes de iniciar la instalación.

d

h

e

f

g

i

j

k

l

m