beautypg.com

Draw-Tite 24794 SPORTFRAME HITCH User Manual

Installation instructions, Nissan sentra, Part numbers

background image

Installation Instructions

Nissan Sentra

Part Numbers:

Hitch Shown In Proper Position

Wiring Access Location: PC3, PC4

Equipment Required: Pull wire (Provided), Sealant

Wrenches: 3/4”

Drill Bits: 1/2”

Fascia

1-1/2” (38.1mm)

1

REMOVE SPARE TIRE FROM TRUNK. Remove jack from tie down bracket.

2

Remove the (2) plastic rivets that fasten the fascia tabs to the vehicle. Note: Remove the center of the rivet with a screwdriver. Rivets to be

reinstalled.

3

Scrape undercoating off bottom of the surface of the trunk reinforcement.

4

Attach pull wire to carriage bolt and through spacer (Item 4) insert using slot located behind the trunk reinforcement making sure the spacer

and carriage bolt sit flat at the bottom.

5

Place reinforcement plate inside spare tire well, at the bottom of trunk. Locate the 1-1/2” length against the bottom of the trunk. Place

between the ribs as shown in Figure 2. Drill two holes.

6

Insert the carriage bolts through the reinforcement bracket and place (2) spacer (Item 5) on the carriage bolts from opposite side of bulkhead.

7

Lift hitch into position onto the two carriage bolts, sandwiching the spacer between the bulkhead and hitch. See Figure 3. Loosely attach

conical washer and hex nuts.

8

Attach bar to trunk reinforcement using conical washer and hex nut (Item 2 & 3).

9

Center hitch on vehicle and Tighten all 1/2-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M).

10

Apply sealant at carriage bolt attachments inside spare tire well to prevent the intrusion of water and exhaust fumes to vehicle interior.

11

Reattach plastic rivets to fascia. Replace spare tire and jack.

Rev. A

2-16-07

24794N

Sheet 1 of 3

z

2007 Cequent Towing Products

Spacer .250 X 1.00 X 2.00 (Rd. Hole)

Qty. (2)

5

Conical Washer

Qty. (3)

2

Hex Nut 1/2-13

Qty. (3)

3

Spacer .250 X 1.50 X 2.00 (Sq. Hole)

Qty. (1)

4

Carriage Bolts 1/2-13 X 2.00 GR5

Qty. (3)

1

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the
RISE position only.

Drawbar Kit:

3594

Fastener Kit: 24794F

2000 LB (908 Kg) Max Gross Trailer Weight

200 LB (90.8 Kg) Max Tongue Weight

24794

60871

77166

Spare tire
well

Reinforcement
plate

1

4

2

3

5

23

23

1

5

Spare tire well

Reinforcement
plate inside of
trunk

Pull wire

Reinforcement
plate

Jack tie down
bracket

Ribs inside of
spare tire well

Drill holes

Locate reinforcement plate
between ribs

REMOVE
SPARE TIRE
BEFORE
DRILLING

Drill holes

Reinforcement plate

5

5

Bulkhead

Jack tie down bracket

Bulkhead

Figure 1

Figure 2

Figure 3.

Overhead view

Trunk

reinforcement

Bottom of trunk cut away
for inside view

Form F206 Rev A 5605