Draw-Tite 24899 SPORTFRAME HITCH - Manual

Installation Instructions
Honda Accord
Acura TL
Acura TSX
Part Numbers:
24899
60325
77287
Hitch Shown In Proper Position
Wiring Access Location: PC3, 4
Equipment Required: Metal Shears, Lubricant or Soapy water,
Die Grinder
Wrenches: 10mm, 11/16”
j
1. Lower exhaust (2) rubber isolator on single exhaust, (4) rubber isolators on dual exhaust. Note: Spraying a lubricant or soapy water on the
metal hanger rod and the rubber isolator helps removal.
2. Remove heat shield(s) and underbody panel (if present). Save panel and fasteners for reinstallation.
3. Check to see if spacer and carriage bolt will fit through access hole, if not modify hole to accept hardware, the illustration above (Figure 2)
shows two ways of achieving this, the first is using a file, the second is by inserting a wrench or prying as shown. Enlarge hole just enough
to get hardware through.
4. Feed spacers and carriage bolts into position using the pull wires provided (both rails). Leave pull wire attached. Note: It is much easier if
bolt and spacer are not engaged while inserting them into frame, refer to illustration. See Figure 3.
5. Hang U-bolt on tow hook.
6. Raise hitch into position with U-Bolt in one of two locations. Feed pull wires through hole in side arm.
7. Attach fasteners as shown. Note: Be careful not to push fasteners into frame rails.
8. Tighten to specification
9. Prior to trimming panel, obtain vehicle owner’s approval or return untrimmed panel.
10. Trim underbody panel (if present) as shown in Figure 4. The dimensions given are estimates and should be confirmed prior to trimming.
After trimming, slide the hitch bracket through the cut in the underbody panel until it is in cut-out region.
11. Raise underbody panel into position and reinstall fasteners.
12. Reattach heat shield(s). Bend heat shield over hitch as needed. Trim minimally around new fasteners if needed.
13. Reattach exhaust. Note: If additional exhaust clearance is required, bend exhaust hanger bracket, which is welded to vehicle frame,
downward.
Tighten all 3/8 GR5 fasteners with torque wrench to 30 Lb.-Ft. (41 N*M)
Tighten all 7/16 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N-M)
z 2012 Cequent Performance Products, Inc. Sheet 1 of 3 24899N 10-10-12 Rev. A
j
Qty. (2) Carriage bolt 7/16-14 X 1.50 GR5
n
Qty. (1) U-Bolt 3/8 GR5
k
Qty. (2) Spacer
o
Qty. (2) Conical washer 3/8
l
Qty. (2) Conical washer 7/16
p
Qty. (2) Hex nut 3/8
m
Qty. (2) Hex nut 7/16
q
Qty. (2) Pull wire 7/16
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
Drawbar must be used in the
RISE position only.
Drawbar Kit:
3593
Fastener Kit: 24899F
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Note: Fasteners typical
both sides
Fascia
l
m
n
o
p
q
Frame
rail
Tow Hook
Forward Location
Shown
Metal File
Wrench
Oblong access hole
Figure 2
Figure 1
Figure 3
Kink Pull wire to keep
spacer independent of bolt
k
Exhaust, heat shield and wheel
well not shown for clarity
Access hole
j
12.75
6.00
6.00
1.00
C
ut
Underbody Panel
Figure 4
Form F206 Rev B 9-17-2012
Accessory Rating A
2008 – 2012 Honda Accord
2008 & Up Acura TL
2008 – 2012 Acura TSX
2013 & Up Honda Accord
Fascia
Tow Hook
Both Locations
Shown