Draw-Tite 24692 SPORTFRAME HITCH - Manual

Installation Instructions
FORD FOCUS SEDAN,
FORD FOCUS 5 DR – ZX5 (HATCHBACK)
FORD FOCUS 3 DR – ZX3 (HATCHBACK)
Part Numbers:
77114
24692
60870
Hitch Shown In Proper Position
Wiring Access Location: PC3, PC4 (SEDAN)
PC1, PC2 (HATCHBACK)
Equipment Required:
Wrenches: 3/4”, 7/8”
Drill Bits: 1/2”
1. RAISE HITCH INTO POSITION.
NOTE: THE DRIVER’S SIDE BRACKET IS POSITIONED INBOARD OF THE TIE DOWN HOOK, PASSENGER’S SIDE BRACKET IS POSISTIONED
OUTBOARD OF THE TIE DOWN HOOK.
NOTE: PLACEMENT OF THE BLOCK WITH 2 HOLES VARIES BY MODEL. SEE FIGURE 1.
2. INSTALL CARRIAGE BOLTS AND BLOCKS THRU VEHICLE TIE DOWN HOOKS AS SHOWN AND LOOSELY INSTALL FLAT WASHERS AND HEX
NUTS.
SEDAN MODEL:
3. FISHWIRE CARRIAGE BOLT AND BLOCK THRU END OF FRAME RAIL AND INTO EXISTING HOLE IN FRAME.
4. INSTALL REMAINING FASTENERS AS SHOWN.
HATCHBACK:
3. USING THE HITCH AS A TEMPLATE, DRILL 1/2” HOLE IN THE FORWARD MOST END OF SLOT IN SIDE BRACKET ON PASSENGER SIDE.
4. FISHWIRE CARRIAGE BOLT AND BLOCK THRU ACCESS HOLE ON THE BOTTOM OF FRAME RAIL.
5. INSTALL REMAINING FASTENERS AS SHOWN.
Tighten all 1/2” fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Rev. G 7-17-07 N24692 Sheet 1 of 3 z 2006, 2007 Cequent Towing Products
NUT – LOCK 1/2-13 Qty. (3)
!
WASHER – CONICAL 1/2” Qty. (1)
5
BLOCK - .25 X 1.00 X 2.00 Qty. (1)
9
WASHER – FLAT 1/2” Qty. (3)
4
BLOCK - .25 X 1.00 X 3.00 Qty. (1)
8
NUT – 1/2-13 Qty. (1)
3
BLOCK - .25 X 1.50 X 2.00 Qty. (2)
7
BLOCK - .25 X 1.50 X 4.00 * Qty. (1)
2
BLOCK – .188 X 1.00 X 2.00 Qty. (1)
6
BOLT – CARRIAGE 1/2-13 X 2.00 GR5 Qty. (4)
1
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry
of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and
wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE
J684.
2000 LB (908Kg) Max Gross Trailer Weight
200 LB (90.8Kg) Max Tongue Weight
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
Drawbar must be used in the
RISE position only.
Drawbar Kit:
3593
Fastener Kit: K24692
*(SEDAN)
*(HATCHBACK)
* POSITION OF THIS BLOCK
VARIES BY MODEL
FASCIA
FRAME RAIL
SIDE BRACKET
ACCESS HOLE
(HATCHBACK)
EXISTING HOLE ON SEDAN, DRILL 1/2” DIA.
HOLE ON HATCHBACK MODELS
TIE DOWN HOOK
ALL MODELS REQUIRE
SPACER BETWEEN HITCH
AND FRAME
6 8 53 1
1 9 4 !
1 7 2 4 !
FIGURE 1
Note: Does NOT fit models with Street Appearance Package
Form F206 Rev A 5605