Atec Agilent-E8267D - Manual (Page 3)

3
Range 1
Option 520 250 kHz to 20 GHz
Option 532 250 kHz to 31.8 GHz
Option 544 250 kHz to 44 GHz
Resolution
CW
0.001 Hz
All sweep modes 0.01 Hz 2
Switching speed 3, 4 < 16 ms (typ) with I/Q modulation off
< 24 ms (typ) with I/Q modulation on
Phase offset Adjustable in nominal 0.1 ° increments
Frequency bands
Band Frequency range N 5
1 250 kHz to 250 MHz 1/8
2 > 250 to 500 MHz 1/16
3 > 500 MHz to 1 GHz 1/8
4 > 1 to 2 GHz 1/4
5 > 2 to 3.2 GHz 1/2
6 > 3.2 to 10 GHz 1
7 > 10 to 20 GHz 2
8 > 20 to 28.5 GHz 3
9 > 28.5 to 44 GHz 5
Accuracy ± [(time since last adjustment x aging rate)
+ temperature effects + line voltage effects
+ calibration accuracy]
Internal timebase reference oscillator
Standard 8 Option UNX
Aging rate < ±3 x 10 -8 /year or < ±3 x10 -8 /year or
< ±2.5 x 10 -10 /day < ±2.5 x 10 -10 /day
after 30 days after 30 days
Temperature effects (typ) < ±4.5 x 10 -9 0 to 55 °C < ±4.5 x 10 -9 0 to 55 °C
Line voltage effects (typ) < ±2 x 10 -10 for < ±2 x 10 -10
±10% change for ±10% change
External reference frequency 10 MHz only 10 MHz only
Lock range ±1.0 ppm ±1.0 ppm
Reference output
Frequency
10 MHz
Amplitude > +4 dBm into 50 Ω load (typ)
External reference input
Amplitude
5 dBm ±5 dB
Option UNX 5 dBm ±5 dB 6
Input impedance 50 Ω (nom)
Operating modes Step sweep of frequency or amplitude or both (start to stop)
List sweep of frequency or amplitude or both (arbitrary list)
Sweep range
Frequency sweep
Within instrument frequency range
Amplitude sweep Within attenuator hold range (see “Output” section)
Dwell time 1 ms to 60 s
Number of points 2 to 65535 (step sweep)
2 to 1601 per table (list sweep)
Triggering Auto, external, single, or GPIB
Settling time
Frequency
< 8 ms 7 (typ)
Amplitude < 5 ms (typ)
Specifications
Frequency
1. Operational, but unspecified, down to 100 kHz.
2. In ramp sweep mode (Option 007), resolution is limited with narrow spans and slow sweep speeds. Refer to ramp sweep
specifications for more information.
3. Time from GPIB trigger to frequency within 0.1 ppm of final frequency above 250 MHz or within 100 Hz below 250 MHz.
4. Add 12 ms (typ) when switching from greater than 3.2 GHz to less than 3.2 GHz.
5. N is a factor used to help define certain specifications within the document.
6. To optimize phase noise 5 dBm ± 2 dB.
7. 19 ms (typ) when stepping from greater than 3.2 GHz to less than 3.2 GHz.
8. Standard performance applies to units with serial numbers ending with 48050000 or greater. For units with lower serial
numbers, refer to the data sheet shipped with the unit or the version of this document dated November 6, 2007.
Step (digital) sweep