Atec Agilent-E8267D - Manual (Page 12)

12
Measured RMS jitter: 1
Standard
Carrier
SONET/SDH RMS jitter Unit intervals Time
frequency data rates bandwidth (µUI) (fs)
155 MHz 155 MB/s 100 Hz to 1.5 MHz 25 158
622 MHz 622 MB/s 1 kHz to 5 MHz 21 34
2.488 GHz 2488 MB/s 5 kHz to 20 MHz 57 23
9.953 GHz 9953 MB/s 10 kHz to 80 MHz 152 15
39.812 GHz 39812 MB/s 40 kHz to 320 MHz 627 16
Option UNX
Carrier
SONET/SDH RMS jitter Unit intervals Time
frequency data rates bandwidth (µUI) (fs)
155 MHz 155 MB/s 100 Hz to 1.5 MHz 23 151
622 MHz 622 MB/s 1 kHz to 5 MHz 19 30
2.488 GHz 2488 MB/s 5 kHz to 20 MHz 56 22
9.953 GHz 9953 MB/s 10 kHz to 80 MHz 152 15
39.812 GHz 39812 MB/s 40 kHz to 320 MHz 626 16
Maximum deviation 2 Frequency Maximum deviation
250 kHz to 250 MHz 2 MHz
> 250 to 500 MHz 1 MHz
> 500 MHz to 1 GHz 2 MHz
> 1 GHz to 2 GHz 4 MHz
> 2 GHz to 3.2 GHz 8 MHz
> 3.2 GHz to 10 GHz 16 MHz
> 10 GHz to 20 GHz 32 MHz
> 20 GHz to 28.5 GHz 48 MHz
> 28.5 GHz to 44 GHz 80 MHz
Resolution 0.1% of deviation or 1 Hz, whichever is greater
Deviation accuracy < ±3.5% of FM deviation + 20 Hz
(1 kHz rate, deviations < N x 800 kHz)
Modulation frequency response 3 (at 100 kHz deviation)
Path [coupling] 1 dB bandwidth 3 dB bandwidth (typ)
FM path 1 [DC] DC to 100 kHz DC to 10 MHz
FM path 2 [DC] DC to 100 kHz DC to 1 MHz
FM path 1 [AC] 20 Hz to 100 kHz 5 Hz to 10 MHz
FM path 2 [AC] 20 Hz to 100 kHz 5 Hz to 1 MHz
DC FM 4 carrier offset ±0.1% of set deviation + (N x 8 Hz)
Distortion < 1% (1 kHz rate, deviations < N x 800 kHz)
Sensitivity ±1 V
peak
for indicated deviation
Paths FM1 and FM2 are summed internally for composite
modulation. Either path may be switched to any
one of the modulation sources: Ext1, Ext2, internal1,
internal2. The FM2 path is limited to a maximum
rate of 1 MHz. The FM2 path must be set to a
deviation less than FM1.
1. Calculated from phase noise performance in CW mode only at +10 dBm. For other frequencies, data rate, or bandwidths,
please contact your sales representative.
2. Through any combination of path1, path2, or path1 + path2.
3. Specifications apply in CW and list/step sweep modes. During ramp sweep operation (Option 007), 3 dB bandwidth is typically
50 kHz to 10 MHz (FM1 path), and 50 kHz to 1 MHz (FM2 path).
4. At the calibrated deviation and carrier frequency, within 5 °C of ambient temperature at time of user calibration.
Frequency modulation
(Option UNT)