Atec Agilent-8753E - Manual (Page 22)

22
HP 8753E accessories, cont’d
HP 85039B type-F calibration kit
Contains a set of 75-ohm type-F standards to calibrate the
HP 8753E and 75-ohm test set for the measurement of
devices with type-F connectors.
Includes HP part number
F-male 75-ohm termination 85039-60007
F-female 75-ohm termination 85039-60004
Specifications for termination DC to 1 GHz: RL ≥ 45 dB
1 to 3 GHz: RL ≥ 38 dB
F-male 75-ohm short 85039-60008
F-female 75-ohm short 85039-60003
F-male 75-ohm open 85039-60009
F-female 75-ohm open 85039-60005
F-female to F-female 75-ohm adapter 85039-60002
F-male to F-male 75-ohm adapter 85039-60006
Typical type-F adapter
characteristics DC to 1 GHz: RL ≥ 40 dB
1 to 3 GHz: RL
≥ 32 dB
F-female to N-male 75-ohm adapter 85039-60013
F-male to N-female 75-ohm adapter 85039-60011
Typical type-F to type-N adapter
characteristics DC to 1 GHz: RL ≥ 38 dB
1 to 3 GHz: RL ≥ 32 dB
Verification kits
Measuring known devices other than the standards used in
calibration is an easy way to verify the proper operation of
an HP 8753E measurement system. HP offers verification
kits which include devices, with data, for verifying the
error-corrected measurements of an HP 8753E and 50-ohm
test sets.
HP 85029B 7-mm verification kit
Contains a set of precision 7-mm devices, with data
traceable to NIST* used to compare the calibrated
performance of an HP 8753E measurement system.
The HP 85031B 7-mm calibration kit is required for
complete verification.
Test-port return cables
Hewlett-Packard offers high quality RF cables used to
connect the HP 8753E and test sets to devices under test.
These cables offer excellent RF shielding for high dynamic
range measurements.
HP 11851B 50-ohm type-N RF cable kit
Recommended for use with the HP 11850C/D three way
power splitters. Kit includes three phase-matched
610-mm (24 in) cables and one 860-mm (34 in) cable.
Return loss > 24 dB to 3 GHz
Phase tracking ± 4° at 1.3 GHz
HP 11857B 75-ohm type-N test port
return cables
A pair of 610-mm (24 in) test port return cables for use
with the HP 8753E or HP 85046B 75-ohm S-parameter
test set.
Return loss > 24 dB to 2 GHz
Phase tracking ± 2° at 1.3 GHz
HP 11857D 7-mm test-port return cables
A pair of 610-mm (24 in) test port return cables for
use with the HP 8753E or HP 85046A, HP 85047A
S-parameter test sets. These cables can be used with
connector types other than 7-mm with the appropriate
precision adapters.
Return loss >24 dB to 3 GHz
>20 dB to 6 GHz
Phase tracking ± 2° at 1.3 GHz
HP 11850C/D three-way power
splitters
HP 11850C HP 11850D
Impedance 50 ohms 75 ohms
Frequency range DC to 3 GHz DC to 2 GHz
Tracking ±25 dB, ±3° ±2 dB, ±2.5°
Equivalent source match 30 dB at 1.3 GHz 30 dB at 1.3 GHz
(ratio or leveling) 20 dB at 3 GHz 20 dB at 2 GHz
Nominal insertion loss 9.5 dB + 1 dB/GHz 7.8 dB
Input port match
DC to 1.3 GHz 20 dB 20 dB
1.3 GHz to Fmax 10 dB 10 dB
Maximum operating level +20 dB +20 dB
Damage level +30 dB +30 dB
RF connectors
RF input 50 ohm type-N (f) 50 ohm type-N(f)
All others 50 ohm type-N (f) 75 ohm type-N(f)
Includes 3 each HP 11852B
50 to 75 ohm
minimum loss pads
Recommended
accessories HP 11851B RF cable kit
HP 11667A 50-ohm power splitter
Frequency range DC to 18 GHz
Typical insertion loss 6 dB
Equivalent source match 26 dB to 4 GHz
21 dB to 8 GHz
17 dB to 18 GHz
Tracking ± 15 dB to 4 GHz
(between output arms) ± 2 dB to 8 GHz
± 25 dB to 18 GHz
Maximum operating level ± 27 dBm
Connectors 50 ohm type-N (f)
1. National Institute of Standards and Technology.