Atec Agilent-8720D - Manual (Page 11)

11
Description Specification Code
Frequency Characteristics
Range
8719D 0.05 to 13.51 GHz S-1
8720D 0.05 to 20.05 GHz S-1
8722D 0.05 to 40 GHz S-1
Accuracy (at 23 °C ± 3 °C) ±10 ppm S-1
Stability
0 °C to 55 °C ±7.5 ppm C
Option 1D5 ±0.05 ppm C
Per year (aging) ±3 ppm C
Option 1D5 ±0.5 ppm C
Resolution 1 Hz S-3
System Characteristics
Maximum Input Level
Damage Level (test port) 30 dBm C
Reference (F) Input Level (Option 089)
Maximum
8719D/8720D –7 dBm C
8722D –12 dBm C
Minimum
8719D/8720D/8722D –34 dBm C
High Level Trace Noise 2
Magnitude (zero-peak)
0.05 to 13.5 GHz 0.03 dB C
13.5 to 20 GHz 0.04 dB C
20 to 40 GHz 0.15 dB C
Phase (zero-peak)
0.05 to 13.5 GHz 0.3° C
13.5 to 20 GHz 0.4° C
20 to 40 GHz 1.5° C
Spectral Purity Characteristics
Harmonics at maximum output level
<–15 dBc C
Phase Noise
to 60 kHz from carrier at 2 GHz <–55 dBc C
to 60 kHz from carrier at 20 GHz <–35 dBc C
Nonharmonic Spurious Signals
at 100 kHz offset <–40 dBc C
at 200 kHz offset <–45 dBc C
at >200 kHz offset <–65 dBc C
Description Specification Code
Power Characteristics
Power Range
8719D/8720D 75 dB C
8722D
0.05 to 20 GHz 70 dB C
20 to 40 GHz 65 dB C
Maximum Output Power
8719D/8720D (Standard, Options. 085, 400) +5 dBm C
8719D/8720D (Option 007) +10 dBm C
8722D (Standard, Options 085, 400)
0.05 to 20 GHz –5 dBm C
20 to 40 GHz –10 dBm C
8722D (Option 007)
0.05 to 20 GHz 0 dBm C
20 to 40 GHz –5 dBm C
Resolution 0.01 dB S-3
Flatness (at 5 dB below maximum output power)
8719D/8720D ±2 dB S-1
8722D ±3 dB S-1
Power Sweep Range
8719D 20 dB S-3
8720D 20 dB S-3
8722D 15 dB S-3
Power Linearity
±5 dB from reference ±0.35 dB S-1
–10 dB from reference ±0.6 dB S-1
+10 dB 1 from reference ±1 dB S-1
Test Reference Power
8719D/8720D (Standard, Options 085, 400) –5 dBm
S-3
8719D/8720D (Option 007) 0 dBm S-3
8722D (Standard, Options 085, 400) –10 dBm S-3
8722D (Option 007)
Specifications and characteristics
Frequency Range (GHz)
Description 0.05 5 0.05 to 2 5 2 to 8 8 to 20 20 to 40 Code
System Characteristics
Dynamic Range
3
8719D/8720D
(Standard, Options 085, 400)
77 dB 100 dB 100 dB 100 dB S-1
8719D/8720D (Option 007) 82 dB 105 dB 105 dB 105 dB S-1
8722D (Standard 4 , Options 085, 400) 67 dB 93 dB 93 dB 91 dB 80 dB 6 S-1
8722D (Option 007) 72 dB 98 dB 98 dB 96 dB 85 dB S-1
Receiver 0.1 dB Compression Input Level 7 20 dBm 16 dBm 15 dBm 8 dBm 3 dBm C
1. Does not apply to 8722D.
2. Trace noise is defined as variation of a high signal level trace due to noise. The
value given represents a noise variation that is three standard deviations away
from the trace’s mean value as measured in a 3 kHz IF bandwidth in th fast
sweep mode (STEP SWP OFF).
3. The dynamic range specifications apply to transmission measurements using
10 Hz IF BW and response and isolation correction or full two-port correction.
Dynamic range is limited by the maximum test port power and the receiver’s
noise floor.
4. With 85133E flexible cable on test port.
5. Rolls off below 840 MHz to specified value at 50 MHz.
6. 77 dB for Option 085.
7. For Option 012 direct sampler input compression levels, refer to page 9.
S-1: This performance parameter is verifiable using performance tests documented in
the service manual.
S-2: Due to limitations on available industry standards, the guaranteed performance
of the instrument cannot be verified outside the factory. Field procedures can
verify performance with a confidence prescribed by available standards.
S-3: These specifications are generally digital functions or are mathematically
derived from tested specifications, and can therefore be verified by functional
pass/fail testing.
C: Non-warranted performance characteristics are intended to provide information
useful in applying the instrument. Performance characteristics are representa-
tive of most instruments, though not necessarily tested in each unit. Not field
tested.