Extron Electronics IPCP Pro Series User Guide - Manual (Page 11)

IPCP Pro Series • Introduction 5
AUDIO INPUTS OVER DTP
RS-232 IR
Tx Rx Tx Rx G
POWER 12V
0.7A MAX SIG LINK
DTP OUT
100-240V ~ -- A MAX
1
2 CONFIGURABLE HDMI HDMI
5
6
7 8 C
RS-232 IR
RS-232 IR
Tx Rx Tx Rx G
Tx Rx Tx Rx G Tx Rx Tx Rx G
HDMI
A
B
3
4
INPUTS OUTPUTS
Tx Rx
RS-232
G
LAN
70V - 100W
RESET
AUDIO INPUTS OUTPUTS
REMOTE
L L 1 R R
L 2 R
3 CLASS 2 WIRING
L 4 R
L 5 R
+48V
+48V
1 2
L R VARIABLE
IN1608 MA
2
MIC/LINE L 6 R
SIG LINK
DTP IN
SIG LINK
DTP IN
SIG LINK
DTP OUT
50/60 Hz
RS-232 IR
OVER DTP
OVER DTP
OVER DTP
AMPLIFIED OUTPUT
LAN eBUS
FLEX I/O RELAYS IR/SERIAL COM 12 VDC
Tx Rx G Tx Rx G Tx Rx G Tx Rx G S G S G S G S G
S G S G S G S G
RTSCTS
IPCP PRO 550
Tx Rx G Tx Rx G Tx Rx G Tx Rx G RTSCTS 1.2A MAX
SWITCHED 12 VDC 40W MAX TOTAL 3 4
1 1 2 3 7
8 4 5 6
2 1 2
5 6
3 4
7 8
1 2
5 6
3 4
7 8 3 2 1 4 G
+V +S -S G
PWR OUT = 12W 100-240V ~ 50-60Hz MAC:
00-05-A6-
XX-XX-XX
S/N:
####### E###### 00-05-A6-XX-XX-XX
PUSH PUSH POWER GUIDE MENU RES 480 480p 720p 1080i 1080p DIRECTV HD SELECT D I R E C T V
1
INPUTS
AUDIO
Tx Rx G Tx Rx
RS-232 IR OVER DTP
RS-232
Component HDMI HDMI
HDMI
HDMI HDMI
Audio
Audio Audio
Audio
Blu-ray Player
Tuner
Media Player
PC
Laptop
Flat Panel Display Flat Panel Display Microphones
CATx Cable
up to 230' (70 m)
Extron
DTP HDMI 230 D Tx
Transmitter
Extron
DTP HDMI 230 Tx
Transmitter
Extron
IN1608 MA
Scaling
Presentation
Switcher
Extron
FF 220T
Plenum 2' x 2' Flat Field
Ceiling Speakers Integrated 100 W amplifier provides audio coverage for 50' x 40' (15.2 m x 12.2 m) room
Extron
IPCP Pro 550
IP Link Pro
Control Processor
Ethernet
Ethernet/Power
RS-232 RS-232
RS-232
IR
Ethernet
Extron
TLP Pro 1520MG
15" Wall Mount
TouchLink Pro
Touchpanel
TCP/IP
Network
Wireless
TouchLink
for iPad
Ethernet
Power
Injector
Figure 3. An IPCP Pro 550 Application
Device Control
The IPCP must be configured in one of the following ways before it will send commands to a
projector, display, or other device:
• An IR, RS-232, or Ethernet driver file can be downloaded from the extensive Extron
driver selection from the Extron website (
www.extron.com/download/index.aspx ).
The driver is saved to a folder and commands from the driver are incorporated into the
configuration file for the control processor and any touchpanels that will work with it.
The configuration file is built and uploaded to the IPCP via GC.
• If a driver is not already available, RS-232 or Ethernet command strings can be
entered directly from a host computer using Global Configurator. These can then be
incorporated into controls within the GC project.
• IR commands can be entered directly from an IR remote control through IR learning
via GC to create a driver that the IPCP can use. IR learning is seldom needed, but it is
convenient for installing new or updated commands into the IPCP Pro Series in the field
in the rare cases when a driver is not already available from Extron.
See the Global Configurator Help file (which comes with the software) for details on setting
up the IPCP and for downloading, programming, or learning device control commands.
PRELIMINARY