GE Industrial Solutions AF-60 LP Micro Drive Operating Instructions - Manual (Page 52)

6.2.11 6-** Analog In/Out
Parameter
Number Parameter Description Default Value 2 Setup Change During
Operation Conver-
sion
Index
Type
6 - 00 Live Zero Timeout Time 10 s All set-ups TRUE 0 Uint8
6 - 01 Live Zero TimeoutFunction [0] Off All set-ups TRUE - Uint8
6 - 10 Terminal 53 Low Voltage 0.07 V All set-ups TRUE -2 Uint16
6 - 11 Terminal 53 High Voltage 10 V All set-ups TRUE -2 Uint16
6 - 12 Terminal 53 Low Current 0.14 mA All set-ups TRUE -2 Uint16
6 - 13 Terminal 53 High Current 20 mA All set-ups TRUE -2 Uint16
6 - 14 Terminal 53 Low Ref./Feedb. Value 0 All set-ups TRUE -3 Int32
6 - 15 Terminal 53 High Ref./Feedb. Value 50 All set-ups TRUE -3 Int32
6 - 16 Terminal 53 Filter Time Constant 0.01 s All set-ups TRUE -2 Uint16
6 - 19 Terminal 53 mode [0] Voltage mode 1 set-up TRUE - Uint8
6 - 22 Terminal 60 Low Current 0.14 mA All set-ups TRUE -2 Uint16
6 - 23 Terminal 60 High Current 20 mA All set-ups TRUE -2 Uint16
6 - 24 Terminal 60 Low Ref./Feedb. Value 0 All set-ups TRUE -3 Int32
6 - 25 Terminal 60 High Ref./Feedb. Value 50 All set-ups TRUE -3 Int32
6 - 26 Terminal 60 Filter Time Constant 0.01 s All set-ups TRUE -2 Uint16
6 - 81 Keypad potentiometer Low Ref. 0 All set-ups TRUE -3 Int32
6 - 82 Keypad potentiometer High Ref. 50 All set-ups TRUE -3 Int32
6 - 90 Terminal 42 Mode [0] 0-20 mA All set-ups TRUE - Uint8
6 - 91 Terminal 42 Analog Output [0] No operation All set-ups TRUE - Uint8
6 - 92 Terminal 42 Digital Output [0] No operation All set-ups TRUE - Uint8
6 - 93 Terminal 42 Output Min Scale 0% All set-ups TRUE -2 Uint16
6 - 94 Terminal 42 Output Max Scale 100% All set-ups TRUE -2 Uint16
6.2.12 7-** Controllers
Parameter
Number Parameter Description Default Value 2 Setup Change During
Operation Conver-
sion
Index
Type
7 - 20 Process CL Feedback 1 Resource [0] No function All set-ups TRUE - Uint8
7 - 30 Process PI Normal/ Inverse Control [0] Normal All set-ups TRUE - Uint8
7 - 31 Process PI Anti Windup [1] Enabled All set-ups TRUE - Uint8
7 - 32 Process PI Start Speed 0 Hz All set-ups TRUE -1 Uint16
7 - 33 Process PI Proportional Gain 0.01 All set-ups TRUE -2 Uint16
7 - 34 Process PI Integral Time 9999 s All set-ups TRUE -2 Uint32
7 - 38 Process PI Feed Forward Factor 0% All set-ups TRUE 0 Uint16
7 - 39 On Reference Bandwidth 5% All set-ups TRUE 0 Uint8
6.2.13 8-** Comm. and Options
Parameter
Number Parameter Description Default Value 2 Setup Change During
Operation Conver-
sion
Index
Type
8 - 01 Control Site [0] Digital and ctrl.word All set-ups TRUE - Uint8
8 - 02 Control Word Source [1] GE Drive RS485 All set-ups TRUE - Uint8
8 - 03 Control Word Timeout Time 1 s 1 set-up TRUE -1 Uint16
8 - 04 Control Word Timeout Function [0] Off 1 set-up TRUE - Uint8
8 - 06 Reset Control Word Timeout [0] No function 1 set-up TRUE - Uint8
8 - 30 Protocol [0] GE Drive 1 set-up TRUE 0 Uint8
8 - 31 Address 1 1 set-up TRUE 0 Uint8
8 - 32 GE Drive Port Baud Rate [2] 9600 Baud 1 set-up TRUE - Uint8
8 - 33 GE Drive Port Parity [0] Even Parity 1 Stop Bit 1 set-up TRUE - Uint8
8 - 35 Minimum Response Delay 0.01 s 1 set-up TRUE -3 Uint16
8 - 36 Max Response Delay 5 s 1 set-up TRUE -3 Uint16
8 - 50 Coasting Select [3] Logic OR All set-ups TRUE - Uint8
8 - 51 Quick Stop Select [3] Logic OR All set-ups TRUE - Uint8
8 - 52 DC Brake Select [3] Logic OR All set-ups TRUE - Uint8
8 - 53 Start Select [3] Logic OR All set-ups TRUE - Uint8
8 - 54 Reversing Select [3] Logic OR All set-ups TRUE - Uint8
8 - 55 Set-up Select [3] Logic OR All set-ups TRUE - Uint8
8 - 56 Preset Reference Select [3] Logic OR All set-ups TRUE - Uint8
8 - 94 Bus feedback 1 0 All set-ups TRUE 0 Int16
AF-60 LP™ Micro Drive Operating Instructions
DET-579A
51
6