Duro-Last Duro-Grip Weather-Tite Hurricane Force PG-1 - Manual

WTT Systems - Roofing Division
n
A Millennium Adhesive Company
n
888.564.9733
n
wttus.com
Hurricane Force
®
PG-1 Pump Grade
Insulation Adhesive
PRODUCT DESCRIPTION
Weather-Tite Hurricane Force PG-1 Pump Grade Insulation
Adhesive is a two component, VOC free, all purpose, low
rise, bulk packaged, polyurethane foamable adhesive that
contains no solvents and sets in minutes.
Application is quick and easy resulting in significant
labor savings for the contractor. Hurricane Force PG-1
Insulation Adhesive is dispensed through the Weather-
Tite Cyclone and Cyclone II pumps or an approved low
pressure pump cart which equally mixes Part 1 and Part
2 of the adhesive, thus providing a quality, consistent
application each time.
BASIC USE
Hurricane Force PG-1 Insulation Adhesive is designed for
use as an adhesive for bonding approved roof insulations
to a building’s structural roof deck, base sheets, other
insulation boards, and smooth or graveled built-up roof
surfaces. It is dispensed in 1/2” to 3/4” (1.27cm - 1.91cm)
wide liquid beads that will quickly spread to a width of
2-3 inches. Hurricane Force PG-1 Insulation Adhesive will
expand and rise to fill minor surface irregularities.
APPROVED INSULATIONS AND SUBSTRATES
HD wood fiber •
Polyisocyanurate •
Perlite •
Polystyrene •
Gypsum cover boards •
Asphaltic cover boards •
Concrete •
Gypsum •
Cemetitious wood fiber •
For a complete list of approved substrates and insulation
types, or additional information, contact our Technical
Department.
Lightweight insulating •
concrete
Wood or steel
•
Modified Bitumen •
membranes and base
sheets (sanded or granule
surfaced)
Approved insulations • (multi-
layer applications)
Smooth or gravel surface
•
built-up roof (re-roof
applications)
FEATURES AND BENEFITS
Better Than Fasteners
No damage to structural •
decking
Eliminates fastener back out
•
No noise associated with •
drilling into concrete
No unsightly fasteners on
•
exposed decks
No fastener or deck corrosion
•
Saves labor •
High strength •
Low Rise Foam
Eliminates •
minor surface
irregularities
No Solvents
Low odor •
VOC free •
No flame hazards •
100% solids •
APPLICATION
1. Extend quick connect spouts in Part 1 and Part 2
box packaging. When using pails stir contents before
material is poured into the holding tanks on approved
pump machine.
2. Invert box and place in tray on the Weather-Tite Cyclone
or Cyclone II pump. Box labeled Part 1 must be in area
of tray labeled “Part 1” and Part 2 in area labeled “Part
2”.
3. If pails are used fill holding tanks as recommended by
pump manufacturer. Part 1 and Part 2 must be equally
mixed. If drums are used follow all recommendations
provided by pump manufacturer.
4. Connect the black Part 1 fitting to the black feed hose
fitting. Connect the gray Part 2 fitting to the gray feed
hose fitting. Operate pump according to manufacturer’s
instructions.
5. Apply Hurricane Force PG-1 Insulation Adhesive directly
to the substrate, using a ribbon pattern. Space beads
12” o.c., to achieve proper coverage rates for insulation
attachment.
6. Hurricane Force PG-1 Insulation Adhesive should be
approximately 70°F (22°C) when being dispensed. As
adhesive is applied, allow to begin rising, then place
insulation board into adhesive. Do not allow the adhesive
to skin over. Eliminate uneven surfaces to ensure
positive contact between the adhesive, insulation board,
and substrate.
7. Unused material can be applied at a later date. Properly
clean dispensing wand and pump unit according to
pump manufacturer’s recommendations.