Veris Industries E51H5 Install - Manual (Page 25)

ZL0109-0C Page 25 of 32 ©2013 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected] 10131
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Other companies’ trademarks are hereby acknowledged to belong to their respective owners.
Installation Guide
Power Monitoring
E51H2, E51H5
TM
# Object
Name
Description R/W NV Units Range Additional Information
AI1 KWh_Net Accumulated Real
Energy: Net (Import -
Export)
R NV kWh -3.4+E38 - 3.4+E38
AI2 KWh_Import Real Energy Import R NV kWh 0 - 3.4+E38
AI3 KWh_Export Real Energy Export R NV kWh 0 - 3.4+E38
AI4 KVARh_Q1 Reactive Energy
Quadrant 1
R NV kVARh 0 - 3.4+E38 The Units property of object AI4 reports that these units are kWh because there
is no unit type in the BACnet standard for KVARh
AI5 KVARh_Q2 Reactive Energy
Quadrant 2
R NV kVARh 0 - 3.4+E38 The Units property of object AI5 reports that these units are kWh because there
is no unit type in the BACnet standard for kVARh
AI6 KVARh_Q3 Reactive Energy
Quadrant 3
R NV kVARh 0 - 3.4+E38 The Units property of object AI6 reports that these units are kWh because there
is no unit type in the BACnet standard for kVARh
AI7 KVARh_Q4 Reactive Energy
Quadrant 4
R NV kVARh 0 - 3.4+E38 The Units property of object AI7 reports that these units are kWh because there
is no unit type in the BACnet standard for kVAh
AI8 Net_KVAh Apparent Energy: Net
(Import - Export)
R NV kVAh -3.4+E38 - 3.4+E38 The Units property of object AI8 reports that these units are kWh because there
is no unit type in the BACnet standard for kVAh
AI9 KVAh_Import Apparent Energy
Import
R NV kVAh 0 - 3.4+E38 The Units property of object AI9 reports that these units are kWh because there
is no unit type in the BACnet standard for kVAh
AI10 KVAh_Export Apparent Energy
Export
R NV kVAh 0 - 3.4+E38 The Units property of object AI10 reports that these units are kWh because there
is no unit type in the BACnet standard for kVAh
AI11 KW_Total Total Instantaneous
Real Power
R kW 0 - Max_Power (AI76)
AI12 KVAR_Total Total Instantaneous
Reactive Power
R kVAR 0 - Max_Power (AI76)
AI13 KVA_Total Total Instantaneous
Apparent Power
R kVA 0 - Max_Power (AI76)
AI14 PF_Total Total Power Factor R -1.00 - 1.00
AI15 Volts_LL_Avg Voltage, L-L, Average
of Active Phases
R Volts
AI16 Volts_LN_Avg Voltage, L-N, Average
of Active Phases
R Volts
AI17 Current
Average
Current, Average of
Active Phases
R Amps
AI18 Frequency Frequency R Hz 45.0 - 65.0 Returns QNAN if frequency is out of range (or no voltage input present on Phase
A)
Analog_Input
Objects Use the Present_Value property of the Analog_Input objects for all read-only numeric variables in the meter other than those
used specifically for device configuration (in the Device Object) or data logging (in the Trend_Log objects). Only the E51H5
supports the data logging capability.
These objects support the Description and Reliability object properties and all required Analog_Input object properties. None
of them are writable. The values that are not instantaneous (i.e., Accumulated Energy, Max Demand, Pulse Input Counts) are
non-volatile. They are not updated while control power is inactive, but their past values are retained when power is restored. The
Present_Value of the accumulated data objects (AI1-AI10 and AI31-AI54) use floating-point data types (all AI objects use floating
point data points). The resolution of the accumulated values decreases as the value grows larger over time and more of the
significant digits precede the decimal point. If the size of the value limits the resolution unacceptably, read and store the current
value offline and reset the accumulators to restore finer resolution.
For complete assurance, check the Reliabilty property for a No_Fault_Detected status before reading the Present_Value. If the
line voltage or input frequency of the system being monitored falls out of the supported range, the corresponding alert bits
(BI1-BI7) are set and the reliability property of any values that cannot be accurately measured under those conditions returns
Unreliable_Other.