Veris Industries H8026 Install - Manual (Page 6)

H8025/8026
Z201640-0H PAGE 6 ©2010 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected] 11101
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
TM
INSTALLATION GUIDE
POINT MAP FOR H8026 (ENHANCED DATA STREAM), N2 PROTOCOL
NPT NPA UNITS POINT DESCRIPTION RANGE/VALUE NOTES
BI 1 kWh, kW* Consumption (accumulation) 100A: 0.0025 kWh/count
300A: 0.01 kWh/count
400A: 0.01 kWh/count
800A: 0.02 kWh/count
1600A: 0.04 kWh/count
2400A: 0.08 kWh/count Intended for use as an accumulator (ACM) type. It should not be read as a binary status.
AI 1 kWh Consumption 100A: 0 to 10737418.24
2400A: 0 to 343597383.7 Allows direct view of kWh accumulator as an AI point. For large values, BI-1 is more precise.
AI 2 kW Real Power 100A: 0 to 83.1
2400A: 0 to 1995.3
AI 3 kVAR Reactive Power 100A: 0 to 83.1
2400A: 0 to 1995.3
AI 4 kVA VA (apparent power) 100A: 0 to 83.1
2400A: 0 to 1995.3
AI 5 Power Factor, total 0 to 1.0 Reads the effective power factor for all phases (not an average of AI-15, AI-16, and AI-17).
AI 6 kW Average Real Power 100A: 0 to 83.1
2400A: 0 to 1995.3 Reads the average real power (kW). This is intended for demand window applications, where
this point is read at the end of each window and then reset via BO-2.
AI 7 kW Mimimum Real Power 100A: 0 to 83.1
2400A: 0 to 1995.3 Reads the min. real power since it was reset via BO-2. Real power is internally monitored in
200msec intervals.
AI 8 kW Maximum Real Power 100A: 0 to 83.1
2400A: 0 to 1995.3 Reads the max. (peak) real power since it was reset via BO-2. Peak power is internally
monitored in 200msec intervals.
AI 9 Volts Voltage, Line-to-Line 0 to 480 Reads the average line to line voltages.
AI 10 Volts Voltage, Line-to-Neutral 0 to 277 Reads the average line to neutral voltages.
AI 11 Amps Current 100A: 0 to 100
2400A: 0 to 2400 Reads the current.
AI 12 kW Real Power, ØA 100A: 0 to 27.7
2400A: 664.8
AI 13 kW Real Power, ØB 100A: 0 to 27.7
2400A: 664.8
AI 14 kW Real Power, ØB 100A: 0 to 27.7
2400A: 664.8
AI 15 Power Factor, ØA 0 to 1.0
AI 16 Power Factor, ØB 0 to 1.0
AI 17 Power Factor, ØC 0 to 1.0
AI 18 Volts Voltage, ØA to ØB 190 to 480 The meter is powered by A-B voltage; it will not operate at low voltage.
AI 19 Volts Voltage, ØB to ØC 0 to 480
AI 20 Volts Voltage, ØA to ØC 0 to 480
AI 21 Volts Voltage, ØA to Neutral 0 to 277
AI 22 Volts Voltage, ØB to Neutral 0 to 277
AI 23 Volts Voltage, ØC to Neutral 0 to 277
AI 24 Amps Current, ØA 100A: 0 to 100
2400A: 0 to 2400
AI 25 Amps Current, ØB 100A: 0 to 100
2400A: 0 to 2400
AI 26 Amps Current, ØC 100A: 0 to 100
2400A: 0 to 2400
ADI 1 Amps Preset kWh, LSW -32768 to 32767 Allows the lower 16 bits of the kWh accumulator to be preset
ADI 2 Preset kWh, MSW -32768 to 32767 Allows the upper 16 bits of the kWh accumulator to be preset
BO 1 Reset kWh 0 = NA
1 = Reset kWh Resets the kWh accumulator to zero. The value will return to "off." **
BO 2 Reset Min/Max/Avg 0 = NA
1 = Reset min/max/avg Command to "on" to reset the AI-5, AI-6, and AI-7. THe value will return to "off." **