Procedure – Spicer Single Drive Axles Service Manual: 34DS, 34RS, 38DS, 38RS, DS340, RS340, DS380, RS380, DS400, RS400, DS3 User Manual
Page 82
Differential Carrier Overhaul (Forward and Rear Axle)
79
Procedure -
1.
Using appropriate sleeve, press bearing cups in cage (see
adjacent drawings).
Note: On rear axles, do not install oil seal in cage until bear-
ing preload is correctly adjusted.
After bearing cups are installed, preselect pinion bearing
spacer using the “trial build-up” procedure described in
the Adjustments Section of this manual.
2.
Press pilot bearing on pinion.
To prevent bearing damage, use suitable sleeve that only
contacts inner bearing race.
3.
Stake pilot bearing using staking tool, this is essential to re-
tain the bearing.
Note: During pinion bearing installation, locate each part in
same position that was used in "Trial Build-up" Pre-
load Test.
IMPORTANT
Forward Axle Pinion.
Press Bearing Cups
in Cage.
I
P R E SS
1
- Cups must be firmly seated in cage
Check with feeler gauge (1.0001")
after installation
NOTE: Install cups one at a time.
Rear Axle Pinion.
Press Bearing Cups
in Cage.
I
P R E SS
I
I
"A" - Caps must be firmly seated in cage
Check with feeler gauge (0.001")
after installation.
NOTE: Install cups one at a time.
IMPORTANT
- DSP40 Tandem Axle - Dare to Compare (2 pages)
- Ratio Flex Program Guide (46 pages)
- Italcardano Wing In A Box Product Line (3 pages)
- Vibration Diagnostics (1 page)
- Carrier-To-Housing Joint Leak (6 pages)
- Front Axle Shafts for the Jeep JK (2 pages)
- S400 Helical Gear Retrofit Kit Installation (2 pages)
- Electric Shift Unit (1 page)
- Approved Lubricant (16 pages)
- Tandem Drive Axles Pro-40 Single Reduction and Single Reduction with Differential Lock (102 pages)
- Kingpin Bushing and Seal Installation Instructions (2 pages)
- ROUND BEARING DRIVESHAFT COMPONENTS (11 pages)
- NEW REDESIGNED 40K TANDEM CARRIERS (6 pages)
- HAXL-PNI-34 (1 page)
- Tandem Drive Axles Service Manual S400 (34 pages)
- HAXL-PNI-31 (1 page)
- Single Drive Axles Service Manual: S170, S190, S590 (76 pages)
- PDU Cover & Outer Pinion Support Bearing for 46,000 LB (2 pages)
- 2007 Spicer Driveshafts Service Manual (32 pages)
- DRIVELINE COMPONENTS CATALOG SLIP YOKE ASSEMBLIES (28 pages)
- DualRange Tandem Axles (8 pages)
- S400 Redesigned Power Divider Parts for Service (2 pages)
- Wing Bearing Products U-Joint Identification Chart (1 page)
- 10 Series Driveshafts (86 pages)
- Driveline Components Catalog - Companion Flanges (24 pages)
- Gear & Pinion and Wheel Diff Case Kits Released for D_R170, D_R190 Models (3 pages)
- DST40-(P) (3 pages)
- 22719X, MODEL 44 POWER LOCK DISC AND PLATE KIT (1 page)
- 126155 (1 page)
- 2011 Spicer Bulletin 3; SERVICE_TECHNICAL INFORMATION (1 page)
- Drive Axles Service Manual Single Axles 2-Speed & Double Reduction (34 pages)
- X510-5DSD BILLS OF MATERIAL DODGE CATALOG CORRECTIONS (2 pages)
- Dana “I” Series (2 pages)
- Elimination of PDU Fill Plug On Tandem Drive Axles (2 pages)
- V Drive Components (1 page)
- RST41 (1 page)
- Torsionally Tuned-40 Tandem Drive Axles (2 pages)
- Drive Axles Illustrated Parts List DSS40, DDS40, RSS40, and RDS40 (28 pages)
- Single Drive Axles Service Manual: S140 Series (44 pages)
- DRIVELINE COMPONENTS CATALOG COUPLING SHAFTS - SPL and 10 Series (16 pages)
- Thick Flange Design Carriers (2 pages)
- 2002 Spicer Bulletin; SERVICE_TECHNICAL INFORMATION (1 page)
- Pre-applied Thread Adhesive Compound on Yoke End Nuts (6 pages)
- U-Tube Breather Assembly (2 pages)
- 130542 (1 page)