Toshiba G3 TOSVERT-130 - Manual (Page 32)

31
11.1 11.1 11.1 11.1 Read Read Read Read----Only Registers Only Registers Only Registers Only Registers
Register Bit Function Bank Mask Adjustment Range Multiplier
01
∼
09 word Reserved    
0A word RX terminal analog input
value 0 FFFF 0000 ~ 7FFF (-100% ~ 0%)
7FFF ~ FFFF (0% ~ 100%) 1
0B word Frequency command
monitor
0 FFFF 0000 ∼ 9C40
(0.00
∼
400.00 Hz)
0.01
0C word Input voltage monitor(Note 1) 0 FFFF 0 ~ 255% 0.1
0D word Output terminal status
monitor
0 00FF Refer to Table 4 (page 32) 
0E word Inverter Status 1 0 FFFF Refer to Table 5 (page 32) 
0F word Inverter Status 2 0 00FF Refer to Table 6 (page 32) 
10 word Present trip 0 00FF 
11 high
byte
4th Past trip (most recent) 0 7F00 
low
byte
3rd past trip 007F Refer to section 11.3 for fault
codes
12 high
byte
2nd past trip 0 7F00 
low
byte
1st past trip (oldest) 007F
13 word Pre-compensation output
frequency
0 FFFF 0000 ∼ 9C40
(0.00
∼
400.00 Hz)
0.01
14 word Post-compensation output
frequency
0 FFFF 0000
∼
9C40
(0.00 ∼ 400.00 Hz)
0.01
15 word Torque current monitor 0 FFFF (Note 2) 0.01
16 word Excitation current monitor 0 00FF 00
∼
FF (0 ~ 255%) 1
17 word PID feedback value 0 FFFF (Note 2) 0.02
18 word Motor overload ratio 0 FFFF 0 ~ 65535 100/65535
19 word Inverter overload ratio 0 FFFF 0 ~ 65535 100/65535
1A word DBR overload ratio 0 FFFF 0 ~ 65535 100/65535
1B word Input power (%) 0 FFFF 0 ~ 6553.5 0.1
1C word Input power (kW) 0 FFFF (Note 3)
1D word Output power (%) 0 FFFF (Note 2) 0.1
1E word Output power (kW) 0 FFFF (Note 2, Note 3)
1F, 20 word Reserved    
21 word Input / output power units 0 0008 0000: 0.01kW
0008: 0.1kW

22 word Command mode status 0 0003 0000: terminal
0001: panel
0002: option
0003: RS232C

23 word Frequency mode selection
status
0 000C 0000: terminal
0004: panel
0008: option
000C: RS232C

24 low
byte
Profibus interface card
software revision    
high
byte
Profibus interface card
software version
25 word Output current (amps)  FFFF 0.0 ~ 6553.5 A 0.1
(Note 1) These monitor voltage units are not affected by the setting of VOLTAGE UNITS SELECTION in
GROUP:UTILITY PARAMETERS ; they are always in units of %.
(Note 2) These registers use signed data (data values larger than 7FFF H are negative). If the register data is
8000 H or larger, the actual value can be obtained by: actual value = - [FFFF H - (register data) + 1].