Operating instructions, Lighting procedure, Shutdown procedure – Regency G36D User Manual

Page 34: First fire, Aeration adjustment

UltraGlow

G36D Zero Clearance Direct Vent Gas Fireplace

OPERATING INSTRUCTIONS

OPERATING

INSTRUCTIONS

1) Read and understand these instructions

before operating this appliance.

2) Check to see that all wiring is correct and

enclosed to prevent possible shock.

3) Check to ensure there are no gas leaks.

4) Make sure the glass in the door frame is

properly positioned. Never operate the

appliance with the glass removed.

5) Verify that the venting and cap are

unobstructed.

6) Ensure that the brick panels are installed.

7) Verify log placement. If the pilot cannot be

seen when lighting the unit, the logs have

been incorrectly positioned.

8) The unit should never be turned off, and on

again without a minimum of a 60 second

wait.

LIGHTING

PROCEDURE

IMPORTANT Gas cock knob cannot be turned

from "PILOT" to "OFF" unless it is partially

depressed.

1) Turn burner OFF using "ON/OFF" switch.

2) Turn gas control knob so indicator points

to "OFF" position and allow 5 minutes for

any gas in the combustion chamber to

escape.

3) Turn gas control knob counterclockwise

so indicator points to the "PILOT" position.

Depress the gas control knob fully. Depress

the igniter button several times until the

pilot lights. After approximately one minute,

release the gas control knob. The pilot ﬂ ame

should continue to burn. If the pilot does

not remain lit, repeat operation allowing a

longer period before releasing gas control

knob.

4) When the pilot stays lit, turn the gas knob

further counterclockwise to the "ON"

position.

5) Use the wall switch, thermostat or remote

control to turn on the unit.

6) Rotate the ﬂ ame height regulator to adjust

the ﬂ ame height higher or lower.

SHUTDOWN

PROCEDURE

1) Use the wall switch, thermostat or remote

control to turn off the main burner.

2) Turn the main gas control clockwise to the

"OFF" position to turn off the pilot.

3) Turn off all electric power to appliance if

service is to be performed.

FIRST FIRE

The ﬁ rst ﬁ re in your ﬁ replace is part of the

paint curing process. To ensure that the paint

is properly cured, it is recommended that you

burn your ﬁ replace for at least four (4) hours

the ﬁ rst time before you use it with the fan on.

When ﬁ rst operated, the unit will release

an odour caused by the curing of the paint,

the burning off of any oils remaining from

manufacturing. Smoke detectors in the house

may go off at this time. Open a few windows to

ventilate the room for a couple of hours.

The glass panel may require cleaning after the
unit has cooled down.

DO NOT ATTEMPT

TO CLEAN THE GLASS WHILE IT

IS HOT.

Note: When the glass is cold and the

appliance is lit, it may cause

condensation and fog the glass.

This condensation is normal and

will disappear in a few minutes as

the glass heats up.

During the ﬁ rst few ﬁ res, a white ﬁ lm

may develop on the glass front as part

of the curing process. The glass should

glass should

be cleaned or the ﬁ lm will bake on and

become very difﬁ cult to remove. Use a

non-abrasive cleaner and NEVER clean

the glass while it is hot.

AERATION

ADJUSTMENT

The air shutter can be adjusted by moving the

adjusting wire up or down. The wire is accessed

through the bottom louver opening. Open the air

shutter for a blue ﬂ ame or close for a yellower

ﬂ ame. The burner aeration is factory set but

may need adjusting due to either the local gas

supply or altitude.

Minimum Air Shutter Opening:

3/16"

Natural Gas

1/2"

Propane

CAUTION: Carbon will be produced if air shutter

is closed too much.

Note: Any damage due to carboning

resulting from improperly setting

the aeration controls is NOT covered

under warranty.

Note: Aeration Adjustment should only

be performed by an authorized

Regency

Installer at the time of

installation or service.

Adjustment Wire: push to close or

pull to open aeration cap.

Closed - Tall yellow

Open - Short Blue

IMPORTANT

To ignite or reignite the pilot,

you must ﬁ rst release the ten-

sion springs below the door.

Only when the pilot holds, without pressure

being applied to the control knob, reapply the

tension springs to the door. The unit must

not be operated with the tension springs

not

unattached.

DO NOT BURN THE APPLIANCE

WITHOUT THE GLASS FRONT IN

PLACE.