KORG XTENDED DEFINITION D32XD - Manual (Page 186)

176
Installing the options
Please read this before you begin instal-
lation
Safety precautions
Warnings
• Before installing an option, be sure to disconnect the
power supply cable and the connecting cables to any
peripheral devices. Failure to do so could cause electrical
shock or may damage the device.
• When installing, repairing, or replacing an option, you
must perform only those actions that the owner ’s manual
directs, and no other.
• Do not apply excessive force to the electronic compo-
nents or connectors on the circuit board(s) of an option,
or attempt to disassemble them.
• This could cause electric shock, fire, or malfunction.
Cautions
• Before touching the option, touch a metal component of
the device into which it will be installed, to discharge any
static electricity that may be present in your body.
Static electricity may damage the electronic components.
• Be careful of any sharp edges or pointed metal parts on
the option or the device into which the option is being
installed.
Sharp edges or points may cause injury.
• Danger of explosion if battery is incorrectly replaced.
Replace only the same or equivalent type.
• When handling an option, never touch parts that are not
related to the installation.
Doing so may cause electrocution or malfunctions.
• When handling an option, be careful not to touch the
leads on the back side of the circuit board (the side oppo-
site that on which the components are mounted).
The sharp points may cause injury.
• Do not allow the option or other device being installed to
become wet, and do not allow objects to be placed on top
of it.
Doing so could cause malfunction.
• When installing an option, be careful that screws or other
parts do not fall into the device into which it is being
installed.
Doing so could cause malfunction.
Please note when installing an option
board (ACB-8, AIB-8 and DIB-8)
• So that static electricity in your body does not damage
the electronic components, touch the ground wire of a
grounded device or an unpainted metallic component to
discharge any static electricity in your body before
installing an option board or memory. Internal compo-
nents of the D32XD/D16XD and of the option boards
may be damaged by static electricity.
• Follow the installation procedure, and be sure that each
part is installed correctly and in the correct orientation.
• Please use care in handling option boards. Dropping
them or applying pressure to them may damage the com-
ponents.
• Avoid touching exposed metal edges of the circuit board,
or portions that need not be handled during installation.
• Be careful not to lose the screws that you remove.
• Do not use screws other than those that are installed in
the option board and the D32XD/D16XD. Using screws
of a different shape or length may damage the unit or
cause it to malfunction.
• Be sure to firmly tighten the screws used for attachment.
• Be sure that the option board is inserted correctly into the
connector or locking pins. After installation, be sure to
check that the board is installed correctly. If the board is
not inserted all the way, faulty contact or power supply
shorts can occur, making the unit malfunction.
• Be careful not to drop parts or the option board into the
inside of the instrument.
If you are unable to retrieve a screw or part that was
dropped inside the instrument, please contact your local
Korg distributor.
• You will need a Philips (“+”) screwdriver.
Use a screwdrive of the appropriate size for the screws.
The screw heads may be damaged if you use a screw-
drive of the wrong size.
Korg Inc. takes no responsibility for any malfunctions or
damage that may occur from improper use or modification
of this product. Nor will Korg Inc. be responsible for any
damages resulting from the loss or destruction of data.
Before you begin working
■ Did you disconnect the power cable?
You must turn off the main power switch of the D32XD/
D16XD, and then disconnect the power cable.
■ Has 30 minutes passed since you turned off the
power?
The interior of the D32XD/D16XD reaches a high tem-
perature during operation. Wait until the interior has
cooled before you begin the installation.
■ Did you back up your data?
An installation error or other problem may cause saved
data to be lost. Back up your important data on a CD be-
fore you perform the installation.