Ibm software commands, Function – Seiko FB-900 User Manual

Page 188

— 8. Software commands —

ESC N

(27)D(78)D

(1B)H (4E)H

Specifies the bottom margin.

≤

255)

The number of lines to be skipped is specified by

“n”

and the

bottom margin is specified in the preset line feed amount.

ESC O

(27)D(79)D

(1B)H (4F)H

Cancels the bottom margin.

ESC P

(27)D(80)D

(1B)H (50)H

Specifies or cancels proportional printing.

n = 0

: Cancels proportional printing.

n = 1

: Specifies proportional printing.

This command is valid when #34 PITCH LOCK is set to NO.

ESC Q

(27)D(81)D

(1B)H (51)H

Printer deselect

Brings the printer into the deselect state when

n=(23)H,(B9)H.

Valid when #71 SELECT IN ENABLE is set to 1 in the
EXTENDED SETUP MODE or set to

I/F

and the

SELECT IN

signal is high.

ESC R

(27)D(82)D

(1B)H (52)H

Initializes the horizontal and vertical tab positions.

Clears the vertical tab position.

ESC S

(27)D(83)D

(1B)H (53)H

Specifies superscript or subscript.

n = 0

: Specifies superscript.

n = 1

: Specifies subscript.

ESC T

(27)D(84)D

(1B)H (54)H

Cancels superscript or subscript.

ESC U

(27)D(85)D

(1B)H (55)H

Specifies or cancels uni-directional printing.

n = 0

: Cancels uni-directional printing.

n = 1

: Specifies uni-directional printing.

ESC W

(27)D(87)D

(1B)H (57)H

Specifies or cancels double-width printing.

n = 0

: Cancels double-width printing.

n = 1

: Specifies double-width printing.

ESC X

(27)D(88)D

(1B)H (58)H

Specifies the right and left margins.

≤

255} {0

≤

255}

n m

ESC Y

(27)D(89)D

(1B)H (59)H

Specifies the 8-dot double-speed double-density graphic mode.

n1 n2

Number of data

k = n1 + n2

256

d1 d2

Horizontal dot density

: 120 dpi

•••

Maximum dots per line

: 1632 dot

Horizontally adjacent dots cannot be printed.

ESC Z

(27)D(90)D

(1B)H (5A)H

Specifies the quadruple-density graphic mode.

n1 n2

Number of data

k = n1 + n2

256

d1 d2

Horizontal dot density

: 240 dpi

•••

Maximum dots per line

: 3264 dot

Horizontally adjacent dots cannot be printed.

ESC [ -

(27,91,45)D

(1B, 5B, 2D)H

Specifies the line type.

n1 n2

Number of data

k = n1 + n2

256

m1 m2

m1 = 1 :

Underscore

m2 = 0

: Cancels the line specification.

m1 = 2

: Center line

m2 = 1

: Single line

m1 = 3

: Upper line

m2 = 2

: Double lines

m2 = 255

: Cancels the line specification.

●

IBM Software commands

Decimal

Hex

Symbol

Function

Code

8-12