8[[`k`fexcjx]\kp]figcxe\i&dflc[\ij – Woodstock W1812 User Manual
Page 11
-8-
N(/()Fne\ijDXelXcD]^%j`eZ\*&'0
J8
=
<
K
P
8[[`k`feXcJX]\kp]fiGcXe\i&Dflc[\ij
I<8;Xe[le[\ijkXe[k_`j
\ek`i\dXelXcY\]fi\lj`e^
k_`jdXZ_`e\.J\i`fljg\i$
jfeXc `ealip dXp fZZli
`] jX]\kp Xe[ fg\iXk`feXc
`e]fidXk`fe `j efk le[\i$
jkff[ Xe[ ]fccfn\[. ;F
EFK i`jb pfli jX]\kp Yp
efki\X[`e^
LJ
Xj `k Xggc`\j kf pfli `e[`m`[lXc nfib`e^
Zfe[`k`fej.Efc`jkf]jX]\kp^l`[\c`e\jZXe
Y\ Zfdgc\k\Ç\m\ip j_fg \em`ifed\ek `j
[`]]\i\ek.=X`cli\kf]fccfn^l`[\c`e\jZflc[
i\jlck `e j\i`flj g\ijfeXc `ealip# [XdX^\
kf\hl`gd\ekfigffinfibi\jlckj.
1. INSTRUCTION
MANUAL. This machine presents significant safety hazards to untrained users. Read/
understand this entire manual before starting the planer/moulder.
2. REACHING INSIDE PLANER/MOULDER. Never reach inside planer/moulder or remove covers when
the planer/moulder is connected to power.
3. INFEED
CLEARANCE
SAFETY.
The infeed roller is designed to pull material into the cutterhead.
Always keep hands, clothing, and long hair away from the infeed roller during operation to pre-
vent serious injury.
4. BODY POSITION WHILE OPERATING. The workpiece may kick out during operation. To avoid get-
ting hit, stand to the side of the planer/moulder during the entire operation.
5. PLANING
CORRECT
MATERIAL. Only plane natural wood stock with this planer/moulder. DO NOT
plane MDF, plywood, laminates, or other synthetic products.
6. GRAIN
DIRECTION.
Cutting across or against the grain is hard on the planer/moulder and may
increase the risk of workpiece kick out. Always cut with the grain or at a slight angle with the
grain.
7. LOOKING
INSIDE
PLANER/MOULDER. Wood chips fly around inside the planer/moulder at a high
rate of speed. DO NOT look inside the machine or remove any guards or covers during operation.
8. KNIFE
CLEARANCE. Before starting the machine, always verify that the moulding knives do not
contact any part of the workpiece guide rails, feed roller swing arm, or the table surface.
=X`cli\
kfm\i`]pbe`]\Zc\XiXeZ\dXpi\jlck`ej\m\i\`ealipXe[dXZ_`e\[XdX^\
9. REMOVING
JAMMED
WORKPIECES.
To avoid serious injury, always stop the planer/moulder and
disconnect power before removing jammed workpieces.
10. DULL/DAMAGED CUTTERS. The planer/moulder may kick out a workpiece at the operator or give
poor finish results if it is operated with dull or damaged blades.
11. UNPLUGGING DURING ADJUSTMENTS. When connected to power, the planer/moulder can be acci-
dentally turned
ON. Always disconnect power when servicing or adjusting machine components.
12. WORKPIECE CLEARANCE. Always verify workpiece has enough room to exit the planer before
starting.